Sony UBP-X800 Benutzeranleitung
4
UBP-X800 / UBP-UX80
4-687-309-11(1)
master page=left
D:\JOB\SONY
DVD\2016\SD160017\4687309111_US\010COVTOC.f
m
• Observe the following as improper handling
may damage the HDMI OUT jack and the
connector.
– Carefully align the HDMI OUT jack on the
connector.
– Carefully align the HDMI OUT jack on the
rear of the player and the HDMI connector
by checking their shapes. Make sure the
connector is not upside down or tilted.
by checking their shapes. Make sure the
connector is not upside down or tilted.
– Be sure to disconnect the HDMI cable
when moving the player.
– Hold the HDMI connector straight when
connecting or disconnecting the HDMI
cable. Do not twist or force the HDMI
connector into the HDMI OUT jack.
cable. Do not twist or force the HDMI
connector into the HDMI OUT jack.
For United States customers. Not applicable in
Canada, including in the province Of Quebec.
Pour les consommateurs Aux États-Unis. Non
applicable au Canada, y compris la province
de Québec.
Canada, including in the province Of Quebec.
Pour les consommateurs Aux États-Unis. Non
applicable au Canada, y compris la province
de Québec.
FCC WARNING
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
This transmitter must not be co-located or
operated in conjunction with any other
antenna or transmitter.
The shielded Interface cable (LAN cable) and
bundled HDMI Cable or High Speed HDMI
Cable with Cable Type Logo must be used
with the equipment in order to comply with
the limits for a digital device pursuant to
Subpart B of Part 15 of FCC Rules.
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
This transmitter must not be co-located or
operated in conjunction with any other
antenna or transmitter.
The shielded Interface cable (LAN cable) and
bundled HDMI Cable or High Speed HDMI
Cable with Cable Type Logo must be used
with the equipment in order to comply with
the limits for a digital device pursuant to
Subpart B of Part 15 of FCC Rules.
b
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct
the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct
the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
receiver is connected.
– Consult the dealer or an experienced radio/
TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio
frequency (RF) Exposure Guidelines. This
equipment should be installed and operated
keeping the radiator at least 20cm or more
away from person’s body (excluding
extremities: hands, wrists, feet and ankles).
exposure limits set forth for an uncontrolled
environment and meets the FCC radio
frequency (RF) Exposure Guidelines. This
equipment should be installed and operated
keeping the radiator at least 20cm or more
away from person’s body (excluding
extremities: hands, wrists, feet and ankles).
Contains FCC ID : MCLJ20H086
Compliance with FCC requirement 15.407©
Data transmision is always initiated by
software, which is the passed down through
the MAC, through the digital and analog
baseband, and finally to the RF chip. Several
special packets are initiated by MAC. These
are the only ways the digital baseband
portion will turn on the RF transmitter, which
it then turns off at the end of the packet.
Therefore, the transmitter will be on only
while one of the aforementioned packets is
being transmitted. In other words, this device
automatically discontinue transmission in
case of either absence of information to
transmit or operational failure.
software, which is the passed down through
the MAC, through the digital and analog
baseband, and finally to the RF chip. Several
special packets are initiated by MAC. These
are the only ways the digital baseband
portion will turn on the RF transmitter, which
it then turns off at the end of the packet.
Therefore, the transmitter will be on only
while one of the aforementioned packets is
being transmitted. In other words, this device
automatically discontinue transmission in
case of either absence of information to
transmit or operational failure.
Frequency Tolerance : ± 20 ppm