Mitutoyo Corporation 02AZD880C Benutzerhandbuch
3) Low battery alarm
If the battery voltage becomes considerably low, the LED display blinks red and the U-WAVE-T sends
a low battery alarm error to the U-WAVE-R. Immediately replace the battery.
(The buzzer type alarms a low battery voltage with a buzzer sound along with a blinking LED.)
a low battery alarm error to the U-WAVE-R. Immediately replace the battery.
(The buzzer type alarms a low battery voltage with a buzzer sound along with a blinking LED.)
IMPORTANT
•
Always use the CR2032 battery (lithium battery).
• The battery supplied at the time of purchase is to check the functions and performance of the
U-WAVE-T. The predetermined length of life may not be met.
• Even for the used CR2032 battery, its voltage may recover in a short time after it is removed from
the U-WAVE-T. However, do not continue to use the old battery. Be sure to replace the battery
with a new one.
• Upon disposal of the battery comply with the related ordinance, regulation, etc.
• When removing or setting the battery, exercises care so as not to break or bend the battery terminal
• When removing or setting the battery, exercises care so as not to break or bend the battery terminal
by applying an undue force to it.
[3] Connect the Connecting cable to U-WAVE-T
• After loaded with the battery, connect the connecting cable (option
, details see section 8)
IMPORTANT
When installing the U-WAVE-T using the connecting cable (02AZD791A, B), particularly
pay attention to the cable orientation. If the cable is connected in the reverse orientation,
data cannot be transmitted.
pay attention to the cable orientation. If the cable is connected in the reverse orientation,
data cannot be transmitted.
Black-marked side => U-WAVE-T
Gray-marked side => Measuring tool
•
Set up the connecting cable with the following procedure.
When screwing or unscrewing the screws, always use the size 0 screwdriver of the
When screwing or unscrewing the screws, always use the size 0 screwdriver of the
standard accessory and tighten or loosen them with a torque of 5 to 8 N•cm.
(1) Remove the two mounting screws (M1.7X0.35X2.5/No.A115-1712C) of the connector cover with
the size 0 screwdriver.
(2) Dismount the connector cover.
(3) Check that the packing (No. 09GAA374) has been attached correctly to the specified position.
(4) Connect the connecting cable with the U-WAVE-T.
(5) While pressing the connecting cable end with fingers, tighten the cable fixing screws so that no gap
(3) Check that the packing (No. 09GAA374) has been attached correctly to the specified position.
(4) Connect the connecting cable with the U-WAVE-T.
(5) While pressing the connecting cable end with fingers, tighten the cable fixing screws so that no gap
appears between the cable connector and the U-WAVE-T.
(6) Make sure that no part of the packing is detached.
(1)
(5)
[4] Register the setting information of U-WAVE-R
After loaded with the battery and connected to a connecting cable, the U-WAVE-T needs to register the
setting information of U-WAVE-R.
Please read the “U-WAVEPAK User’s Manual“ in “PDF_Manual” folder of the CD supplied as a standard
accessory of U-WAVE-R for a detailed registering method and content.
“Adobe Reader” of Adobe Systems INC. is necessary to read.
setting information of U-WAVE-R.
Please read the “U-WAVEPAK User’s Manual“ in “PDF_Manual” folder of the CD supplied as a standard
accessory of U-WAVE-R for a detailed registering method and content.
“Adobe Reader” of Adobe Systems INC. is necessary to read.
IMPORTANT
• “Registering the setting information” should be performed by DATA switch of the connecting
cable before connecting to the Measuring tool.
• The registered information is stored after changing battery.
[5] Connecting to Measuring tool
• After registering the setting information, connect the U-WAVE-T to the Measuring tool.
• Clamp the cable leading to a Measuring tool using the supplied cable clamp or a Velcro fastener so
that measurement is not interfered and the LED display of the U-WAVE-T can be easily viewed.
[6] Functions
1) Data communication
The U-WAVE-T performs data communication with DATA switch as shown below
.
Operations
DATA switch push-down time t
LED
Transmits measurement data.
t ≤ 2sec
None
Transmits the Cancel command.
2 sec < t ≤ 5 sec
Orange blinking
0.1 sec interval
Executes U-WAVE-R search.
5 sec < t ≤ 10 sec
Orange blinking
0.3 sec interval
NOTE
• The Cancel command is a command to inform a U-WAVE-R of data error when wrong
measurement data is transmitted to the U-WAVE-R due to an operating error. However, the
wrong measurement data is not canceled by the command. It is to inform that the previous
data is different from measuring value.
wrong measurement data is not canceled by the command. It is to inform that the previous
data is different from measuring value.
• When the U-WAVE-R search is executed, U-WAVE-T is connected with U-WAVE-R that
can be registered.
• If the DATA switch is held down for more than 10 seconds, the orange LED stops blinking
can be registered.
• If the DATA switch is held down for more than 10 seconds, the orange LED stops blinking
and nothing will function.
The U-WAVE-T can check whether to have performed normal communication with a
U-WAVE-R by a specific LED display (and buzzer sound).
However, buzzer sounds are available only for the buzzer type U-WAVE-T.
U-WAVE-R by a specific LED display (and buzzer sound).
However, buzzer sounds are available only for the buzzer type U-WAVE-T.
Description of state
LED
Buzzer sound
Wireless communication has been
properly completed.
properly completed.
Green LED blinking
Short 2 times
• Wireless communication has failed.
• An error has occurred.
• An error has occurred.
Red LED blinking
Long 1 time
2) Initializing the setting information
If communication is disabled while using the U-WAVE-T, first refer to Troubleshooting
In U-WAVE-R User’s Manual, if communication is still disabled, initialize the setting information
registered in section 4 to default settings, and then retry communication.
Initialize the setting information with the following procedure.
(1) Remove the battery being loaded. For information about how to remove the battery, refer to
In U-WAVE-R User’s Manual, if communication is still disabled, initialize the setting information
registered in section 4 to default settings, and then retry communication.
Initialize the setting information with the following procedure.
(1) Remove the battery being loaded. For information about how to remove the battery, refer to
section 2.
(2) While holding down the DATA switch on the connecting cable connector, reload the battery in
place. The setting information is initialized.
(3) Remount the battery cover, and set up the U-WAVE-T.
IMPORTANT
Once initialization is performed, the setting information used until then is all cleared.
Mitutoyo Corporation
20-1, Sakado 1-Chome, Takatsu-ku, Kawasaki-shi, Kanagawa 213-8533, Japan
[7] Specifications
1) U-WAVE-T for Japan and EU (02AZD730A , 02AZD880A)
1) U-WAVE-T for Japan and EU (02AZD730A , 02AZD880A)
Country
Japan, Europe
Model
IP67 type
Buzzer type
Code No.
02AZD730A
02AZD880A
Certification number
005NYCA0474(Japan)
005NYCA0476(Japan)
Protection class
IP67
-
With/without buzzer
Without
With
Transmission output
Less than 1 mW (0 dBm)
Distance of communication
Approx. 20 m (line-of-sight distance under office environments)
A Conformity standard
Japan
ARIB STD-T66
Europe
EN 50371：2002
EN 300 440-1 V1.3.1 and EN 300 440-2 V1.1.2
EN 301 489-01 V1.6.1 and EN 301 489-03 V1.4.1
2) U-WAVE-T for U.S.A and Canada (02AZD730C , 02AZD880C)
Country
U.S.A, Canada
Model
IP67 type
Buzzer type
Code No.
02AZD730C
02AZD880C
Certification number
VXU-02AZD730C (U.S.A)
4396B-02AZD730C (Canada)
VXU-02AZD880C (U.S.A)
4396B-02AZD880C (Canada)
Protection class
IP67
-
With/without buzzer
Without
With
Transmission output
Less than 0.5 mW (-3 dBm)
Distance of communication
Approx. 14 m (line-of-sight distance under office environments)
A Conformity standard
U.S.A
・47 CFR Part 15.247:(Subpart :C) ・47 CFR Part 15,(Subpart :B)
Canada・
RSS-210 (Issue 7) and RSS-Gen (Issue 2) ・ICES 003 (Issue 4)
3) Common Specifications
Item
Description
Wireless communication protocol
IEEE802.15.4 compatible
Communication frequency
2.405 to 2.475 GHz
Used band
15 channels (at intervals of 5 MHz)
Modulation method
DSSS (Direct Sequence Spread Spectrum)
Wireless communication speed
250 Kbps
LED display
Green/orange/red: 3 discrete color display
Battery
CR2032 (3V): 1 piece
Battery life
400,000 times
Operating temperature (humidity)
0 to 40°C (20 to 80%RH, with no condensation)
Storage temperature (humidity)
-10 to 60°C (20 to 80%RH, with no condensation)
External dimensions
44 X 29.6 X 18.5 (mm)
U-WAVE-T mass
Approx. 23 g
4) Standard accessories
・
User’s manual (this manual) No. 99MAL108B2 ・Size 0 screwdriver No. 05CZA619
・
Lithium battery
CR2032C(B)N ・Warranty card
5) Optional accessories
No. 02AZD790A to G: Connecting cables (For details see section 8.)
[8] Connecting Cables
As for connecting cables, it is necessary to select a cable compatible with a Measuring tool to be used.
Use an appropriate connecting cable from among those in the following table.
Use an appropriate connecting cable from among those in the following table.
U-WAVE-T side
Measuring tool side
(The connector shape and color differs depending on the
Measuring tool to be used. )
(The connector shape and color differs depending on the
Measuring tool to be used. )
Black
DATA switch
Parts No. Model
Series No,
Product Name
02AZD790A
Water-resistant type
with data out switch type
Water-resistant type
with data out switch type
Color: Light gray
500
500
571
572
573
500
571
572
573
ABS Coolant Proof Caliper CD-PMX/PM/GM
Super Caliper CD-SPM
ABS Coolant Proof Depth Gage
Super Caliper CD-SPM
ABS Coolant Proof Depth Gage
VDS-PMX
ABS Coolant Proof Digimatic Scale Units
SD-G
ABS Coolant Proof Exclusive Caliper
NTD-PMX/PM
02AZD790B
Water-resistant type with
data out switch type
Water-resistant type with
data out switch type
Color: Light gray
293
293
293
---
329
350
350
---
468
Coolant Proof Micrometer
MDC-MJ/MJT
Coolant Proof Micrometer
MDE-MJ
Coolant Proof Exclusive Micrometer （The end of the mark is –MJ）
Depth Micrometer
Depth Micrometer
DMC-M
Coolant Proof Digimatic Micrometer Heads MHN-M/MJ/MJN
Digimatic Exclusive Micrometer （The end of the mark is –M/PM）
Digimatic Holtest
Digimatic Exclusive Micrometer （The end of the mark is –M/PM）
Digimatic Holtest
HTD-R
02AZD790C
With data out switch type
With data out switch type
500
571
572
573
571
572
573
---
ABS Digimatic Caliper CD-CX/C
ABS Digimatic Depth Gage VDS-/DCX/DC
ABS Digimatic Scale Units SD-D/SDV-D
ABS Digimatic Caliper CD-SC
ABS Digimatic Exclusive Caliper （The end of the mark is –CX/C）
ABS Digimatic Depth Gage VDS-/DCX/DC
ABS Digimatic Scale Units SD-D/SDV-D
ABS Digimatic Caliper CD-SC
ABS Digimatic Exclusive Caliper （The end of the mark is –CX/C）
02AZD790D
10 pins type
178
179
318
515
518
519
542
543
544
544
179
318
515
518
519
542
543
544
544
572
574
574
Surftest SJ-201/301/401/402
Digi-Derm DGE
Litematic VL-A/AS/AH
CERA Height Master HMD-C
QM-Height QMH-S
Digital Mu-Checker M
Display Unit EB/EC-D/EF
Digimatic Indicator ID-H/ID-F
Laser Scan Micrometer LSM-9506
Laser Scan Micrometer LSM-6200/6900
(It applies when using Digimatic Codeout unit.（02AGC840）)
Difference/Sum Unit SD-U1
Heightmatic HDF
Digi-Derm DGE
Litematic VL-A/AS/AH
CERA Height Master HMD-C
QM-Height QMH-S
Digital Mu-Checker M
Display Unit EB/EC-D/EF
Digimatic Indicator ID-H/ID-F
Laser Scan Micrometer LSM-9506
Laser Scan Micrometer LSM-6200/6900
(It applies when using Digimatic Codeout unit.（02AGC840）)
Difference/Sum Unit SD-U1
Heightmatic HDF
02AZD790E
6 pins type
164
227
227
293
293
227
227
293
293
---
339
337
468
515
568
810
810
337
468
515
568
810
810
Digimatic Micrometer Heads
MHD-M
Digimatic Micrometer Heads
CLM-MH
Soft-Touch Micrometer
CLM
Quickmike MDQ
Exclusive Quickmike
Exclusive Quickmike
（
The end of the mark is –QM）
Digimatic Micrometer
MDC-M
Digimatic Exclusive Micrometer
（
The end of the mark is -DM）
Digimatic Tubular Inside Micrometer
IMJ-M
Digimatic Tubular Inside Micrometer
IMZ-M
Digimatic Holtest
HTD
Digital Height Master
HME-DM
ABS Borematic
SBM-C
Hardness Testing Machine
HM-100/200/HV-100/HH-411
Rockwell Type Hardness Testing Machines
HR-500
02AZD790F
A frat form straight type
A frat form straight type
192
500
511
543
543
550
551
552
570
547
572
574
575
811
500
511
543
543
550
551
552
570
547
572
574
575
811
Digimatic Height Gage HDM-A/HD-A
Digimatic Caliper
Digimatic Caliper
CD
ABS Digimatic Bore Gage
CG-D
ABS Digimatic Indicator
ID-S
ABS Digimatic Indicator
ID-C
Digimatic Caliper
CD
Digimatic Caliper
CD
Digimatic Carbon Fiber Caliper
CFC
ABS Digimatic Height Gage
HDS-HC/C
ABS Digimatic Depth Gage
ABS Digimatic Scale Units
ABS Digimatic Scale Units
SD-E/SDV-E/SD-V/SDV-F
Heightmatic HDF-N
ABS Digimatic Indicator
ABS Digimatic Indicator
ID-U
Hardness Testing Units
HH-300
02AZD790G
Water-resistant type with
frat form straight type
Water-resistant type with
frat form straight type
543
ABS Digimatic Indicator
ID-N/ID-B
ＫＡＷＡＳＡＫＩ, JAPAN