WONDERS TECHNOLOGY CO. LTD. DS1771 Benutzerhandbuch

1

2

5 6 7

3

4

+

Long press: Skip next           Short press:Volume up.

Long press: Skip previous   Short press:Volume down.

2

4

2. Mode indicator 

press

Press

press

press

Press

Line in

5

7

6 Reset port

SoundBox Color

Enable Bluetooth on your device and choose DOSS Soundbox Color 

from the list. 

Bluetooth

Quick f

Slow flashing blue

Mode indicator

If pairing is successful, the LED will change to a slow flashing blue and 

your phone will confirm that the connection has been established. 

If the pairing process fails after 60 seconds, please repeat the above 

steps 1 through 5. 

7.4 x 3 x1.9inch

6W x 2

75dB

80Hz-20KHz

1.06lb

Wonders Technology Co.,Ltd

Email:Support@dossav.com

Website:www.dossaudio.com 

Follow us on Facebook: 

1.

Switch the CloudFox speaker to Bluetooth mode,you can press the 

‘play/pause’ button for 3 seconds to keep it in pairing status.

2.

Run the Alexa app, tap ‘Continue’ and Select Bluetooth .

3.
4.

Speaker's battery will have to be charged at least 8-10 hours prior to 

first use. Moving forward, the battery will only take 3 hours to recharge. 

Place your smart device and wireless speaker no more than 3 feet 

away from each other. 

Upon powering on, a tone will be heard along with a flashing blue LED 

light also accompanied by a prompt notification that the speaker has 

entered into pairing mode. 

To end a call, tap the             button once again. You may also 

end the call directly via your cell phone.

You can connect the Amazon Echo Dot with the speaker via 3.5mm 

Aux-in cable or via Bluetooth. Here is how to connect via Bluetooth: 

The DOSS Soundbox Color  speaker should appear in the list of 

Bluetooth devices. If not, press the "Play/Pause" button for 3 seconds 

and try again. If you see our device listed, please tap it to complete the 

pairing process. 

Download the Amazon Alexa App, follow the standard setup 

procedure to get  the Echo dot connected to your home Wi-Fi.

If a call was received while listening to music, playback will resume 

automatically once the call has ended.

Bluetooth

Problem

Solution

others

Not paired with Bluetooth 

transmitter

Cannot Pair with Bluetooth 

devices

Press Play/Pause button for 3 

seconds,then have a try to pair it 

again.

Cannot play music after 

pairing with the laptop

Please select 'DOSS SoundBox Color' 

as the default playback device.

The song cuts off during 

playback

Please check if the Bluetooth distance 

is more than 33 feet or the battery 

level is low.

There is noise during 

playback

Laptop prompts to install 

driver

This driver is not special for 

SoundBox Color,it's for your laptop 

Bluetooth function, please contact 

the computer company or windows

Cannot turn off the speaker

Customer Service Email

support@dossav.com

Use the needle or wire to poke the 

reset port DOSS SoundBox Color

Please press Play/ Pause button 

for 3 seconds or contact with the 

transmitter' s customer service 

for help

Could be caused by the interference 

of charging. Try changing the location 

of the device and do not charge it 

during playback. 

top

Steady green

FCC Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the 

following two conditions: (1) This device may not cause harmful interference, and (2) 

this device must accept any interference received, including interference that may 

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential 

installation. This equipment generates, uses and can radiate radio frequency energy 

and, if not installed and used in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by 

turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the party 

responsible

for compliance could void the user's authority to operate the equipment.

This equipment complies with FCC radiation exposure limits set forth for an 

uncontrolled environment.

This transmitter must not be co-located or operating in conjunction with any other 

antenna or transmitter.