Valups Corp. VTV-A10 Benutzerhandbuch
Terms and Functions of Each Parts
Antenna
①
An antenna for receiving ATSC-
M/H broadcasting signal. Please
pull out the antenna to its
maximum length if the signal is
weak.
M/H broadcasting signal. Please
pull out the antenna to its
maximum length if the signal is
weak.
②
Power & Battery LED
Indicator
It indicates remaining battery
power status when the device is in
use and indicates whether the
battery is recharging correctly or
not.
It indicates remaining battery
power status when the device is in
use and indicates whether the
battery is recharging correctly or
not.
③
Status LED Indicator
It shows whether VTV-A10 successfully catch available ATSC-M/H
channel information and the receiving sensivalupsy for ATSC-M/H signal.
channel information and the receiving sensivalupsy for ATSC-M/H signal.
④
Wi-Fi LED Indicator
Indicates the connection status with Smart phone through Wi-Fi and also
show data transmission status between two devices.
show data transmission status between two devices.
Reset Hole
⑤
You can press into this hole with a pin to reset the product if there is any
problem. Press the power button and immediately press the reset hole
with a pin while holding the power button, then VTV-A10 will turn off and
turn on again. After booting up, finally VTV-A10 will be initialized to its
original state when you purchased.
(*) Please do not operate this function when the power & battery indicator
LED is blinking.
problem. Press the power button and immediately press the reset hole
with a pin while holding the power button, then VTV-A10 will turn off and
turn on again. After booting up, finally VTV-A10 will be initialized to its
original state when you purchased.
(*) Please do not operate this function when the power & battery indicator
LED is blinking.
Power
⑥
Button
Turns VTV-A10 on/off. Press to power on and hold for 3 seconds to power
off.
off.
The video playback may not be smooth depending on the performance
of smart phones or Wi-Fi communication environment.
of smart phones or Wi-Fi communication environment.
②
③
⑥
⑤
⑦
①
④
Guides for the LED Indicators
You can check the ATSC-M/H signal reception status and operation status
with LED Indicators, of which colors change in each situation as follows:
with LED Indicators, of which colors change in each situation as follows:
■ Power & Battery LED Indicator (at the Top Place)
Status
Details
Off
VTV-A10’s power is off.
Red/Green
(On)
When VTV-A10 is recharged from USB power adaptor or
USB ports in PC, the LED turns into solid red, and finally
turns into solid green if the recharge completes.
Red/Orange/
Green
(On)
Once VTV-A10 is on, the LED indicator is blinking in 3
seconds to show remaining battery power status. Red
blinking is 30% or less, orange blinking is between 30 ~
70%, and Green blinking is 70% or above.
■ Status LED Indicator (at the Center)
Status
Details
Off VTV-A10’s
power
is
off.
Green
(Fast Blinking)
It indicates the VTV-A10 is turning (booting-up) on. It
takes about 20 sec to complete boot up procedure.
Green
(Slow Blinking)
Now searching for available ATSC-M/H broadcasting
frequency.
Green
(Solid On)
Channel searching was succeeded and ready to watch
ATSC-M/H broadcast.
Orange
(On)
Failed to search for ATSC-M/H Broadcasting frequency or
channels.
Red
(On)
VTV-A10 is not operating in a normal manner. Press the
Reset Hole on the side with a pin to reboot.
■ Wi-Fi LED Indicator (at the Bottom)
Status
Details
Off
Wi-Fi is not in normal operation. Or VTV-A10 is
connected with PC through an USB cable.
Green
(On)
VTV-A10 is ready to transmit data to a smart phone over
Wi-Fi connection.
Green
(Flickering)
VTV-A10 is transmitting data to a smart phone over Wi-
Fi.