Graupner GmbH & Co. KG MC-20 Benutzerhandbuch
70
Detail program description - Copy / Erase
Copy model
¼ model
Select the »Copy model
¼ model« sub-menu with
the
cd selection keys of the left or right touch pad
then tap the
SET
key.
Copy flight en kopieren
Erase model
Copy modelodell –> Modell
Expor t to SD-Kar te
Impor t fromn von SD-Kar te
=>
OFF
ON
Please select
RF on/off?
If the message shown above should appear, the
transmitter's RF module is still active. Switch the RF
module off as described on page 80 then also, if a
receiver system is currently switched on, switch off
that receiver too. This is to be done for reasons of
safety.
Choose the model to be copied with the
transmitter's RF module is still active. Switch the RF
module off as described on page 80 then also, if a
receiver system is currently switched on, switch off
that receiver too. This is to be done for reasons of
safety.
Choose the model to be copied with the
cd selection
keys of the left or right touch pad …
03
04
05
01
¿¿¿
free
¿¿¿
01:23hR16
Ultimate
02
Graubele
1234g/080811
00:44hR12
Starlet
BELL47G
00:33hR08
00:22hR08
Test
trim needed
Copy from model:
… then, following the change into the "Copy to
model" window caused by another tap on the
model" window caused by another tap on the
SET
key of the right touch pad, the destination memory
can be selected with the
can be selected with the
cd selection keys of the left
or right touch pad. Yet another tap on the
SET
key
will then confi rm the copy process or a tap on
ESC
key will cause the copy to be canceled. A memory
location which is already occupied can be overwritten.
location which is already occupied can be overwritten.
03
04
01
01:23hR16
Ultimate
02
Graubele
1234g/080811
00:44hR12
Starlet
BELL47G
00:33hR08
00:22hR08
Test
trim needed
Select model to be erased :
… whereby another tap on the
SET
key will cause the
confi rmation request …
Model really
Ultimate
to be erased?
NO
YES
02
… to appear. A
NO
response will cause the process
to be canceled and a return to the previous screen.
Selecting the YES response with the
Selecting the YES response with the
f selection key
of the left or right touch pad followed by confi rmation
of the selection with a brief tap on the
of the selection with a brief tap on the
SET
key will
erase the selected model memory.
Caution:
This erase process cannot be undone. All data
in the selected model memory will be erased
completely.
This erase process cannot be undone. All data
in the selected model memory will be erased
completely.
Note:
If the currently active model memory is to be
erased, a model type "Winged" or "Heli" must be
defi ned immediately after the erase process. If,
however, an inactive memory location is erased, it
will subsequently appear in "Model select" list as
"
If the currently active model memory is to be
erased, a model type "Winged" or "Heli" must be
defi ned immediately after the erase process. If,
however, an inactive memory location is erased, it
will subsequently appear in "Model select" list as
"
ÄÄÄ
free
ÄÄÄ
".
Copy / Erase
Erase or copy model
¼ model, copy from or to SD card, copy fl ight phases, store/cancel changes
Use the
cd selection keys of the left or right touch
pad to select the »Copy / Erase« menu …
Ser vo adjustment
Stick mode
Control adjust
Dual Rate / Expo
Channel 1 cur ve
Switch display
Model select
Copy / Erase
Suppress codes
Suppress models
Base setup model
Model type
Ser vo adjustment
Stick mode
Control adjust
Dual Rate / Expo
Channel 1 cur ve
Switch display
Model select
Copy / Erase
Suppress codes
Suppress models
Base setup model
Helicopter type
… then briefl y tap the center
SET
key of the right
touch pad.
Erase model
Copy flight phase
Erase model
Copy model –> model
Expor t to SD
Impor t from SD
=>
Select the "Erase model" sub-menu with the
cd
selection keys of the left or right touch pad then
briefl y tap on the
briefl y tap on the
SET
key.
Choose the model to be erased with the
cd
selection keys of the left or right touch pad …