Moxa ioLogik E2260 IOLOGIK E2260 Benutzerhandbuch
Produktcode
IOLOGIK E2260
1
w w w. m o x a . c o m
i n f o @ m o x a . c o m
Automation Controllers
ioLogik E2260
Front-end intelligence that supports 24 Click&Go™ rules
›
Active Messaging with real-time stamp, including SMS,
›
SNMP Trap with I/O status, TCP, and email
Supports SNMPv1/v2c/v3 protocol
›
I/O peer-to-peer function
›
Built-in web console
›
PC utility: Auto detection of installed modules
›
Windows/WinCE VB/VC.NET and Linux C APIs
›
Moxa’s ioLogik E2260 is a new type of active micro controller that
can be used as an RTU (Remote Terminal Unit). Active Ethernet micro
controllers are a kind of PC-based data acquisition and control device
that use proactive, event-based reporting to control I/O devices. Unlike
traditional RTUs, which are passive and must poll for data, Moxa’s
Active OPC Server makes seamless connection with SCADA systems
can be used as an RTU (Remote Terminal Unit). Active Ethernet micro
controllers are a kind of PC-based data acquisition and control device
that use proactive, event-based reporting to control I/O devices. Unlike
traditional RTUs, which are passive and must poll for data, Moxa’s
Active OPC Server makes seamless connection with SCADA systems
a reality. In addition, SNMP is used for communicating with an NMS
(Network Management System) for IT field users. The I/O status of
an Active Ethernet micro controller can be reported and controlled
automatically on-site based on user specified conditions. This report-
by-exception approach, which is new to PC-based monitoring, requires
far less bandwidth than traditional polling methods.
(Network Management System) for IT field users. The I/O status of
an Active Ethernet micro controller can be reported and controlled
automatically on-site based on user specified conditions. This report-
by-exception approach, which is new to PC-based monitoring, requires
far less bandwidth than traditional polling methods.
Active Ethernet micro controller with 6 RTD inputs and
4 digital outputs
Introduction
Specifications
LAN
Ethernet: 1 x 10/100 Mbps, RJ45
Protection: 1.5 KV magnetic isolation
Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP, HTTP,
CGI, SNTP
Protection: 1.5 KV magnetic isolation
Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP, HTTP,
CGI, SNTP
Serial Communication
Interface: RS-485-2w: Data+, Data-, GND
Serial Line Protection: 15 KV ESD for all signals
Serial Line Protection: 15 KV ESD for all signals
Serial Communication Parameters
Parity: None
Data Bits: 8
Stop Bits: 1
Flow Control: None
Baudrate: 1200 to 115200 bps
Protocol: Modbus/RTU
Data Bits: 8
Stop Bits: 1
Flow Control: None
Baudrate: 1200 to 115200 bps
Protocol: Modbus/RTU
RTD
Channels: 6
Input Type: Pt, JPt, Ni, RTD sensor, resistor
Sampling Rate: 12 samples/sec (all channels)
Resolution: 0.1°C or 0.1 ohm
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
Input Impedance: 625K ohms (min.)
Input Type: Pt, JPt, Ni, RTD sensor, resistor
Sampling Rate: 12 samples/sec (all channels)
Resolution: 0.1°C or 0.1 ohm
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
Input Impedance: 625K ohms (min.)
Digital Output
Channels: 4, sink, 36 VDC, 200 mA
I/O Mode: DO or Pulse Output
Pulse Wave Width/Frequency: 10 ms/100 Hz
I/O Mode: DO or Pulse Output
Pulse Wave Width/Frequency: 10 ms/100 Hz
Over-voltage Protection: 45 VDC
Over-current Limit: 750 mA
Over-temperature Shutdown: 175°C
Isolation: 3K VDC or 2K Vrms
Over-current Limit: 750 mA
Over-temperature Shutdown: 175°C
Isolation: 3K VDC or 2K Vrms
Power Requirements
Power Input: 24 VDC nominal, 12 to 36 VDC
Power Consumption: 282 mA typical @ 24 VDC
Power Consumption: 282 mA typical @ 24 VDC
Physical Characteristics
Wiring: I/O cable max. 14 AWG
Dimensions: 115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in)
Weight: under 250 g
Dimensions: 115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in)
Weight: under 250 g
Environmental Limits
Operating Temperature:
Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)
Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)
Regulatory Approvals
EMI: FCC Part 15, CISPR (EN55022) class A
EMS: IEC 61000-4, IEC 61000-6
Safety: UL508
Shock: IEC 60068-2-27
Freefall: IEC 60068-2-32
Vibration: IEC 60068-2-6
EMS: IEC 61000-4, IEC 61000-6
Safety: UL508
Shock: IEC 60068-2-27
Freefall: IEC 60068-2-32
Vibration: IEC 60068-2-6
Note: Please check Moxa’s website for the most up-to-date certification status.
Warranty
Warranty Period:
5 years
Details: See www.moxa.com/warranty