Zucchetti Axess S.p.A. 90401-15 Benutzerhandbuch
904 RFID2 LEGIC Shortform-ENG-16.doc
p.n.19040222
Reader technology
LEGIC SC2560 based proximity read-write interface for ISO15693 & ISO14443A tags
Transponder types
LEGIC prime (13.56MHz proprietary), advant (ISO15693 and ISO14443A)
Interface
Electrical: According to model p/n and pins.
Data format: According to configuration pins.
Reading range
About 4 cm with ISO cards.
Don’t mount the reader directly on metal surface.
Visual indication
Two LEDs (Red and Green) driven by connecting Yellow and Grey wires to GND.
Power supply
p/n 904.205.15: 5 Vdc. (+/-10%), 150mA typical.
p/n 904.206.15: 5 to 18 Vdc, 150mA typical.
Dimensions
101 x 44 x 23 mm (outline)
Temperature range
-25° to +60°C.
Interface Cable
300 cm, PVC, 10 wires (904.205.15) or 12 wires, no connector (904.206.15).
This device only conforms to
all the standards of the CE
mark if the installation and
user instructions contained in
this document are followed
correctly.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference. Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
INSTRUCTIONS FOR FCC ID LABELING
Module type: transmitter 90401-15
FCC-ID: SYL90401-15
This intends to inform you how to specify the FCC ID of our transmitter module 90401-15 on your final product. Based on the Public Notice from FCC, the
product into which our transmitter module is installed must display a label referring to the enclosed module. The label should use wording such as “Contains
transmitter module FCC ID: SYL90401-15” or “Contains FCC ID: SYL90401-15”, any similar wording with the same meaning may be used.
Module type: transmitter 90401-15
FCC-ID: SYL90401-15
This intends to inform you how to specify the FCC ID of our transmitter module 90401-15 on your final product. Based on the Public Notice from FCC, the
product into which our transmitter module is installed must display a label referring to the enclosed module. The label should use wording such as “Contains
transmitter module FCC ID: SYL90401-15” or “Contains FCC ID: SYL90401-15”, any similar wording with the same meaning may be used.
904 RFID/2 LEGIC 13.56MHz proximity R/W modules
p/n 904.205.15 - Magstripe output or TTL serial module
p/n 904.206.15 - RS232 or Wiegand or buffered Clock &
Data module.
Data module.
Data transmission
Readers are preprogrammed for automatic retrieving and
transmission of any of a few common known segments data,
or (if known segments are missing) of the UID code always
present in all cards. UID is output in Magstripe emulation as
binary conversion to a string of 20 decimal figures (10 figures
for each 4Bytes/32bits group). Note: The preprogrammed
logical output, is not proper for the Wiegand output. Proper
logical output format, in general, can be reprogrammed with
the TMC LEGIC configuration utility or CSW2000 program by
LEGIC.
transmission of any of a few common known segments data,
or (if known segments are missing) of the UID code always
present in all cards. UID is output in Magstripe emulation as
binary conversion to a string of 20 decimal figures (10 figures
for each 4Bytes/32bits group). Note: The preprogrammed
logical output, is not proper for the Wiegand output. Proper
logical output format, in general, can be reprogrammed with
the TMC LEGIC configuration utility or CSW2000 program by
LEGIC.
WARNING: Make all the connections before applying the
power supply to the reader. Never connect the configuration
pins (Brown, GreyPink or BluRed) to the Vdc.
power supply to the reader. Never connect the configuration
pins (Brown, GreyPink or BluRed) to the Vdc.
2Color wires - 904.206.15 only
Configuration Pins
Output Format ↓
Brown
GreyPink
BluRed
Green (x)
Serial/RS232
TO GND
19200,N,8: TO GND
38400,N,8: OPEN
38400,N,8: OPEN
OPEN
(RXD)
Magstripe – Clk&Data
OPEN
TO GND
OPEN
TO GND
Wiegand
(904.206.15 only)
OPEN
OPEN
TO GND
TO GND
AXESS TMC srl
Via della Filanda, 22 - 40133 Bologna - Italy
Tel:+39 051 3519311 - Fax: +39 051 3519399
www.axesstmc.com
904.205.15
904.206.15
Blue
GND
Red
Power 5 (+/-0.5) Vdc
Green
RXD
serial TTL
RXD -
RS232 (x)
White
TXD
serial TTL
/ Data
TXD -
RS232
Pink
Clock
Data0 / Clock
Black
Data1 / Data
Yellow
GREEN LED
OFF
=
OPEN
,
ON
=
TOGND
Gray
RED LED OFF =
OPEN
, ON =
TOGND
Violet
Reserved for FW upgrades – do not connect.
1 2 3 4 5 6 7 8
Output for TMC PROX & TRAX
5
Red
Power 5Vdc
4
Blue
GND
3
White
Data Output
2
Pink
Clock Output
1
(n.c.)
Connector - 904.205.15 only
The TTL output version only is supplied with a 8-pin
MOLEX connector. It is factory configured for using (as a
magnetic emulation reader) with TMC 914.003.20 HotMAX
boards. Connection to PROX (and TRAX) terminals is also
possible changing the pins order and reducing the
connector as shown in the rightmost table.
MOLEX connector. It is factory configured for using (as a
magnetic emulation reader) with TMC 914.003.20 HotMAX
boards. Connection to PROX (and TRAX) terminals is also
possible changing the pins order and reducing the
connector as shown in the rightmost table.
Note: to modify the pin connections or change the
connector size, just press a little with a screwdriver into the
corresponding rectangular hole and pull the wire at the
same time.
Then re-insert it in the required position.
connector size, just press a little with a screwdriver into the
corresponding rectangular hole and pull the wire at the
same time.
Then re-insert it in the required position.
Output Assignment for TMC MAX
1
Blue
GND
2
Red
Power 5 Vdc
3
Pink
Clock Output
4
5
White
Data Output
6
7
Yellow
GREEN LED
8
Gray
RED LED
WARNING: connect first GND blue wire, then other connections, leaving Vdc last one.