Impinj Inc. XARRAY Benutzerhandbuch
Speedway Revolution Installation and Operations Guide Octane 4.11
Appendix A: Regions of Operation
Appendix A: Regions of Operation
38
Revision 4.11 Copyright ©2014, Impinj, Inc.
Impinj Model Number IPJ-A0400-EU1, CSL CS-777-1 (Brickyard) with 7 foot
integrated pigtail to RP-TNC male connector; 0 dBd composite gain
integrated pigtail to RP-TNC male connector; 0 dBd composite gain
MTI MT-242032/NLH (left-hand CP) or MT-242032/NRH (right-hand CP) with Ntype
female connector (antennas available in IP54 or IP67 ratings); 1.85 dBd gain
female connector (antennas available in IP54 or IP67 ratings); 1.85 dBd gain
Sensormatic Electronics Corp. Model number IDANT10CEU25 (left-hand CP only) with
6 foot Belden 7806A coaxial cable (0.1 dB per foot loss) to RP-TNC male connector;
3.25 dBd composite gain
6 foot Belden 7806A coaxial cable (0.1 dB per foot loss) to RP-TNC male connector;
3.25 dBd composite gain
Warning:
The use of any antenna not
listed above may damage the Reader or
adversely affect performance.
adversely affect performance.
Avertissement:
L'utilisation de toute
antenne ne figurent pas ci-dessus peut
endommager le lecteur ou affecter les
performances.
endommager le lecteur ou affecter les
performances.
Operation in Other Global Regions
Installation
Because Speedway Revolution is capable of up to +32.5 dBm conducted power on the
housing RF connector, professional installation is required.
housing RF connector, professional installation is required.
Operation in China, Israel, Indonesia, Malaysia, Singapore, and Vietnam
Regulations in these countries allow a maximum radiated power of 33 dBm ERP (Effective
Radiated Power) for high power RFID systems. The maximum Speedway Revolution output
power is determined by the following equation:
Radiated Power) for high power RFID systems. The maximum Speedway Revolution output
power is determined by the following equation:
Maximum power setting (in dBm) = 33 – Antenna Gain (in dBd) + Cable loss (in dB)
For example, for an application with an antenna gain of 6 dBd and cable loss of 2 dB, the
Reader output power can be set no higher than 33-6+2 = 29 dBm. The maximum transmit
power of Speedway Revolution is 32.5dBm measured at the RF antenna port.
Reader output power can be set no higher than 33-6+2 = 29 dBm. The maximum transmit
power of Speedway Revolution is 32.5dBm measured at the RF antenna port.
Note:
It is important to apply the antenna gain expressed in dBd (dB with respect to a
dipole), which is equivalent to the isotropic antenna gain (in dBi) minus 2.15 dB. The
antenna gain used to set the output power must be the maximum linear gain of the
applicable antenna. Approved antenna vendors, model numbers, and associated gain are
listed in the following section.
antenna gain used to set the output power must be the maximum linear gain of the
applicable antenna. Approved antenna vendors, model numbers, and associated gain are
listed in the following section.
Operation in Australia, Brazil, Hong Kong, New Zealand, Taiwan, Thailand, Uruguay, and
Latin America
Latin America
Regulations in Australia, Brazil, Hong Kong, New Zealand, Taiwan, Thailand, Uruguay, and
Latin America allow maximum radiated power of 36 dBm EIRP. The Speedway Revolution
output power may be increased to provide the maximum allowable EIRP subject to a
maximum conducted power allowance as well. The maximum conducted power at the
antenna connector can be no more than 30 dBm. The maximum allowable output power of
the Reader can be set to satisfy both the conductor and radiated maximum criteria. The
expression for the maximum Reader power setting is:
Latin America allow maximum radiated power of 36 dBm EIRP. The Speedway Revolution
output power may be increased to provide the maximum allowable EIRP subject to a
maximum conducted power allowance as well. The maximum conducted power at the
antenna connector can be no more than 30 dBm. The maximum allowable output power of
the Reader can be set to satisfy both the conductor and radiated maximum criteria. The
expression for the maximum Reader power setting is: