Wilson Electronics LLC 2B5325 Benutzerhandbuch

Wilson Electronics, Inc . has been a leader in the wireless communications industry for over 40 years . The company 

designs and manufactures Signal Boosters, antennas and related components that significantly improve cellular phone 

signal reception and transmission in a wide variety of applications, both mobile (marine, RV, vehicles) and in-building 

(home, office, M2M) .
With extensive experience in antenna and Signal Booster research and design, the company’s engineering team uses a 

state-of-the-art testing laboratory, including an anechoic chamber and network analyzers, to fine-tune antenna designs 

and performance . For its Signal Boosters, Wilson Electronics uses a double electrically shielded RF enclosure and cell 

tower simulators for compliance testing .
Wilson Electronics Signal Boosters feature patented Smart Technology   ™ that enables them to automatically adjust 

their power based on cell tower requirements .  By detecting and preventing oscillation (feedback), signal overload and 

interference with other users, these Smart Technology   ™ Signal Boosters improve network cell phone areas without 

compromising carrier systems .
All products are engineered and assembled in the company’s 55,000-square-foot headquarters in St . George, Utah . 

Wilson Electronics has product dealers in all 50 states as well as in countries around the world .

 Warning:   Do not plug in the power supply until the Outside Antenna cable is attached to the Sleek .

 Warning: 

RF Safety: The Sleek cradle/Signal Booster must be installed with a separation of at 

least 8 inches from all persons and must not be located in conjunction with any other 

antenna or Signal Booster .

 Warning 

RF Safety: The FCC requires that a cell phone with cradle attached may only be used 

with the cradle mounted as illustrated in this installation guide . A cell phone held near 

the ear must be without the cradle attached .

 Warning: 

RF Safety: All Inside Antennas used with this Signal Booster may not have gain (less 

cable Loss) that exceeds 15 dBi and must be located at least 8 inches from all people . 
Outside mobile antennas may not have gain (less cable loss) that exceeds 5 .7 dBi and 
must be located at least 9 inches from all people. Outside fixed antennas may not have 
gain that exceeds 15 dBi (less cable loss) and must be located at least 22 inches from 
all people . All antennas shown on page 1 meet these requirements .

 Warning:   DO NOT use phone covers that have chrome or any other metallic surface . It may block 

cellular signals .

All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee .  If, for any reason, the performance of any product is not acceptable, simply 

return the product directly to the reseller with a dated proof of purchase .

Wilson Electronics Signal Boosters are warranted for one (1) year against defects in workmanship and/or materials .  Warranty issues may be resolved by returning the 

product directly to the reseller with a dated proof of purchase .  
Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) 

number supplied by Wilson Electronics .  Wilson Electronics shall, at its option, either repair or replace the product . Wilson Electronics will pay for delivery of the repaired or 

replaced product back to the original consumer within the continental United States .  
This warranty does not apply to any Signal Boosters determined by Wilson Electronics to have been subjected to misuse, abuse, neglect, or mishandling that alters 

or damages physical or electronic properties .
Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void your warranty .  
RMA numbers may be obtained by contacting Technical Support at 866-294-1660 .  
Disclaimer:      The  information  provided  by  Wilson  Electronics,  Inc .  is  believed  to  be  complete  and  accurate .    However,  no  responsibility  is  assumed  by  Wilson 

Electronics, Inc . for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use . 

Copyright © 2012 Wilson Electronics, Inc .  All rights reserved .

This device complies with part 15 of the FCC Rules . Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and (2) this device must accept any interference 

received, including interference that may cause undesired operation. Changes or modifications made 

that are not expressly approved by Wilson Electronics could void authority to operate this equipment .