Wilson Electronics LLC 460003 Benutzerhandbuch

460003

Antenna connectors

F-Female

Antenna impedance

50 ohms

Dimensions

6 .5 x 4 .5 x 1 .75 inch  

(16 .5 x 11 .4 x 4 .4 cm)

Weight

1 .28 lbs (0 .580 kg)

Frequency

704-746 MHz, 776-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz

Maximum Power

700 MHz 

Band 17

700 MHz 

Band 13

800 MHz

1900 MHz

1700/2100 MHz

22 .5

24 .2

24 .4

22 .6

24 .1

Maximum Power

700 MHz 

Band 17

700 MHz 

Band 13

800 MHz

1900 MHz

1700/2100

MHz

4 .7

4 .5

6 .9

10 .4

2 .4

Noise Figure (typical downlink/uplink)

5 dB nominal

Isolation

> 110 dB

110-240 V AC, 50-60 Hz, 8 W

Each Signal Booster is individually tested and factory set to ensure FCC compliance . The Signal Booster cannot be adjusted without factory reprogramming or 

disabling the hardware . The Signal Booster will amplify, but not alter the incoming and outgoing signals in order to increase coverage of authorized frequency 

bands only . If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected . If a detected signal is too high in a frequency band, 

or if the Signal Booster detects and oscillation, the Signal Booster will automatically turn the power off on that band . For a detected oscillation the Signal 

Booster will automatically resume normal operation after a minimum of 1 minute . After 5 (five) such restarts, any problematic bands are permanently shut 

off until the Signal Booster has been manually restarted by momentarily removing the power from the Signal Booster . Noise power, gain, and linearity are 

maintained by the Signal Booster’s microprocessor.  

Wilson Electronics, LLC

3301 East Deseret Drive, St . George, UT 84790

For additional Technical Support visit www .WilsonElectronics .com 

or email at: tech@wilsonelectronics .com

Phone: 866-294-1660    Local: 435-673-5021    Fax: 435-656-2432

www .twitter .com/WilsonCellular      www .facebook .com/WilsonCellular

111202_DBPro4G_RevP_01 .23 .14

All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee .  If for any reason 

the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof 
of purchase .

Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials .  

Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase . 

Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of 

purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics .  Wilson Electronics 

shall, at its option, either repair or replace the product . Wilson Electronics will pay for delivery of the repaired or 

replaced product back to the original consumer if located within the continental U .S .

This warranty does not apply to any Signal Booster determined by Wilson Electronics to have been subjected to 

misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties .

Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void your warranty .

RMA numbers may be obtained by contacting Technical Support at 866-294-1660 .

  

The information provided by Wilson Electronics, LLC is believed to be complete and accurate .  However, no 

responsibility is assumed by Wilson Electronics, LLC for any business or personal losses arising from its use, or for any infringements of 

patents or other rights of third parties that may result from its use .

Copyright © 2013 Wilson Electronics, LLC .  All rights reserved .

U .S . Patent Nos . – 7,221,967; 7,729,669; 7,486,929; 7,409,186; 7,783,318; 8,583,034; 8,583,033

Before use, you must register this consumer device with your wireless provider and have their consent . The majority of wireless providers have consented to the 

use of signal boosters. You must operate this device with approved antennas and cables as specified in the install guide. If requested by the FCC or a cellular 

service provider, the device will need to be turned off immediately . Warning: E911 location information may be inaccurate for calls placed while using this device .