ECORE TECHNOLOGY COMPANY LIMITED HT1087A Benutzerhandbuch
(3) Please do not touch the light bulb when it still hot.
Pair with your mobile phone
First time pairing
Turn on the Light bulb speaker by turn the on/off switch of the light socket to “on”, and the Light bulb speaker will
lights up with a beep.
Activate Bluetooth on your mobile phone and select “Light bulb speaker”.
After paired for the first time, the Light bulb speaker can pair to your mobile phone automatically when it is on.
Turn on the Light bulb speaker by turn the on/off switch of the light socket to “on”, and the Light bulb speaker will
lights up with a beep.
Activate Bluetooth on your mobile phone and select “Light bulb speaker”.
After paired for the first time, the Light bulb speaker can pair to your mobile phone automatically when it is on.
Trouble shooting
No connection:
z Make sure the Bluetooth connection of your mobile phone is on;
z Make sure the speaker is on;
z The working range of the Bluetooth is about 8 meters w/o block, try closer;
z Pair the speaker again.
z Make sure the Bluetooth connection of your mobile phone is on;
z Make sure the speaker is on;
z The working range of the Bluetooth is about 8 meters w/o block, try closer;
z Pair the speaker again.
Maintenance
Cleaning the Case:
To clean the case, first unplug the power. To remove dirt or dust, wipe the casing with a soft, dry, lint‐free cloth. To remove
stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent and then wipe the casing.
Do not use alcohol, benzene, thinners or other chemical detergents as these can cause the casing to be warped or discolored.
Storage
Always power off the Light bulb speaker when you finish using it.
If the unit will not be used for an extended period, be sure to follow these guidelines:
Do not store the unit in a damp environment
z Avoid exposing the unit to very high or low temperatures
z Avoid prolonged exposure to direct sunlight.
z Avoid exposing the unit to very high or low temperatures
z Avoid prolonged exposure to direct sunlight.
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.