Interactive Toy Concepts Limited 50XXXTX27 Benutzerhandbuch
Item# 50400
Congratulations on
your purchase of the
HELICOPTER
1 x HELICOPTER
1 x CONTROLLER
1 x USB CHARGING WIRE
Do not modify your Helicopter! Any changes or modifications to this product are strictly prohibited and will void product warranty.
Do not attempt to charge the Helicopter from any other source other than the USB charging wire provided to charge the Lithium
Polymer Battery or you will void the warranty! Any attempts at charging other products with the USB charging wire are strictly
prohibited and will void the warranty! The Lithium Polymer Battery is permanently built-in to the Helicopter. Any attempts to tamper
with or remove the Lithium Polymer Battery inside the Helicopter is stictly prohibited and will void the warranty. Do not point the
Antenna directly at the Helicopter! Do not use in strong winds, use only in VERY mild conditions! Do not use in rain, snow or around
heavy debris! Do not use near electrical lines or high voltage wires or other sources of electricity! Do not use around smoke or flames!
Do not use around water and other liquids! Do not use in crowded areas! Do not use around air conditioning! Do not use around air vents!
Do not use around ceiling fans! Do not use around large obstacles! Do not use in very small spaces! Do be conscious of changes in your area!
Keep moving Rotors and Propellers away from eyes, hands, hair and loose clothing. Always turn off your Helicopter and Controller when
not in use. Always remove the batteries from the Controller during storage. Always use new and fresh Alkaline Batteries in Controller for
not in use. Always remove the batteries from the Controller during storage. Always use new and fresh Alkaline Batteries in Controller for
optimal performance. Battery performance will greatly influence flight characteristics. Keep your Instruction Manual in a safe place for
future reference. Parental supervision required.
The Controller takes one 9V battery (Not included).
This radiocommunication device complies with all the requirements of the Industry Canada Standard RSS-310. Operation is subject to the following two conditions:
1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.
Field Strength and measurement distance: 27.145MHz - 61.35 dBuV/m at 3 meter. 49.860 MHz - 59.00 dBuV/m at 3 meter.
Industry Canada Notice: Canada only.
Manufactured by and distributed by Interactive Toy Concepts Ltd.
INS-50400-100318-US
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This
device must accept any interference received including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. Note: This equipment
has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These Limits are designed to provide reasonable
protection against harmful interference in a residential installation. This generates, uses and can radiate radio frequency energy and if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try and correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment
and receiver - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV
technician for help.
device must accept any interference received including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. Note: This equipment
has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These Limits are designed to provide reasonable
protection against harmful interference in a residential installation. This generates, uses and can radiate radio frequency energy and if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try and correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment
and receiver - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV
technician for help.