Leviton Manufacturing Co. Inc. RZD10 Benutzerhandbuch

:

•   To be installed and/or used in accordance with appropriate electrical codes and regulations.
•   If you are unsure about any part of these instructions, consult a qualified electrician.
•   To avoid overheating and possible damage to this device and other equipment, do not install to control a receptacle, fluorescent lighting, a motor- or a transformer 

operated appliance.

•   Use with magnetic low-voltage transformers, incandescent, or 120V halogen fixtures only. Use a Leviton electronic low-voltage dimmer to control electronic 

(solid state) low-voltage transformers.

•   When magnetic low-voltage circuits are operated at a dim level, with all lamps inoperative, excess current may flow through the transformer. To avoid possible
  transformer failure due to overcurrent, use a transformer that incorporates thermal protection or a fuse at the primary windings.
•   Vizia

TM

 RF dimmers are not compatible with standard 3-way or 4-way switches. They must be used with compatible Vizia

TM

 RF controllers for multi-location dimming.

:

•    Use only one (1) Vizia

TM

 RF dimmer in a multi-location circuit with up to 9 coordinating Vizia

TM

 remotes without LEDs or Vizia

TM

 RF remotes for multi-location. The remote(s) 

will turn the light on at the brightness level selected at the dimmer.

•   Total minimum load must exceed 40W.
•   Dimmer may feel warm to the touch during normal operation.
•   Recommended minimum wall box depth is 2-1/2".
•   Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.
•   Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.
•   Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

Single Pole (One location) or 3-Way (Multi-location)

Cat. No. RZM10-1L, 1000VA (Lighted)

120VAC, 60Hz

IMPORTANT : For 3-Way applications, note that one of the screw 

terminals from the old switch being removed will usually be a different 

color (Black) or labeled Common. Tag that wire with electrical tape and 

identify as the common (Line or Load) in both the dimmer wall box and 

remote wall box.

1 - #12 w/ 1 to 3 #14, #16 or #18

2 - #12 w/ 1 or 2 #16 or #18

1 - #14 w/ 1 to 4 #16 or #18

2 - #14 w/ 1 to 3 #16 or #18

DI-000-RZM10-00A-X2

•   Pull off pre-cut insulation from dimmer leads.
•   Make sure that the ends of the wires from the wall box are 

(cut if necessary).

•   Remove insulation from each wire in the wall box as shown.
•   For Single-Pole Application, go to Step 4a.
•   For 3-Way Coordinating Remote (no LEDs) Application, go to 

 CONNECT A MAGNETIC LOW-VOLTAGE DIMMER

ONLY TO THE PRIMARY (HIGH-VOLTAGE) SIDE OF A MAGNETIC

LOW-VOLTAGE TRANSFORMER.
•   Green or bare copper wire in wall box to Green dimmer lead.
•   Line Hot wall box wire to Black dimmer lead.
•   Load wall box wire to Red dimmer lead.
•  Line Neutral wall box wire to White dimmer lead.
•   Yellow/Red dimmer lead should have Red insulation label affixed.

 

NOTE: If insulating label is not affixed to Yellow/Red dimmer lead,

  use electrical tape to cover.
•  

Proceed to Step 5.

 FOR MAGNETIC LOW-VOLTAGE APPLICATIONS,

CONNECT DIMMER ONLY TO THE PRIMARY (HIGH-VOLTAGE)

SIDE OF A MAGNETIC LOW-VOLTAGE TRANSFORMER.
NOTE: When using the coordinating remote without LEDs, the 

dimmer can be installed on either the Line or Load side of the 3-way 

circuit.
NOTE: Maximum wire length from dimmer to all installed remotes 

cannot exceed 300 ft.
•   Green or bare copper wire in wall box to Green dimmer lead.
•   Line Hot (common) wall box wire identified (tagged) when 

removing old switch to Black dimmer lead.

•   First Traveler wall box wire to Red dimmer lead 

(note wire color). 

This traveler from the dimmer must go to the terminal screw on 

the remote marked “RD”.

•   Remove Red insulating label from Yellow/Red dimmer lead.
•   Second Traveler wall box wire to Yellow/Red dimmer lead 

wire color). This traveler from the dimmer must go to the terminal 

screw on the remote marked “YL/RD”.

•  Line Neutral wall box wire to White dimmer lead.

Slotted/Phillips Screwdriver 

Electrical Tape

Pliers 

 

 

Pencil

Cutters 

 

 

Ruler

In multi-dimmer installations, the reduction of the dimmer’s capacity

is required. Refer to the chart for maximum load per dimmer.

If installing Dimmer in a single device application, proceed with the 

INSTALLING YOUR DIMMER section. If installing Dimmer in a multi-

device application, proceed as follows:

Your Dimmer includes three color options. The Dimmer ships with the 

White frame attached. To change color of frame, proceed as follows:

NOTE: Use check boxes           when Steps are completed.

OFF POWER at circuit breaker or fuse and test that power 

is off before wiring!

Single Pole
1.  Line (Hot)

2.  Neutral

3.  Ground

4.  Load 

NOTE: If the wiring in your wall box does not resemble any 

of these configurations, consult a qualified electrician.

3-Way
1.  Line or Load (see important instruction)

2.  Neutral

3.  Ground

4.  First Traveler – note color

5.  Second Traveler – note color

Pull off pre-cut insulation from dimmer leads. Make sure that 

the ends of the wires from the wall box are 

necessary). Remove insulation from each wire in the wall 

box as shown:

Low-voltage dimmers are rated in Volt-Amps (VA). The maximum bulb 

wattage is determined by the efficiency of the transformer in the low-

voltage lighting system. Transformer efficiencies will vary from different 

manufacturers; consider 80% efficient as average. Use the chart to 

determine maximum bulb wattage for typical transformer efficiency ratings.

650W

650VA

800W

800VA

1000W

1000VA

Incand

Mag LV

520W

640W

800W

1000VA