Leviton Manufacturing Co. Inc. RZP15 Benutzerhandbuch

Incandescent 1800W         Fluorescent: 1800VA          Resistive: 15A        Motor: 1/2HP        TV: 8A

120VAC, 60Hz

DI-000-RZP15-00A-X1

• To be installed and/or used in accordance with appropriate electrical codes and regulations.

• If you are unsure about any part of these instructions, consult a qualified electrician.

Leviton’s Vizia™ Z-wave™ components are
designed to communicate with each other via
Radio Frequency (RF) to provide remote control of
your lighting. Using RF technology allows Leviton
to provide the greatest signal integrity possible.
Each module in Leviton’s Vizia™ RF component
line is a Z-wave™ enabled device. In a Z-wave™
network, each device is designed to act as a router.
These routers will re-transmit the RF signal from
one device to another until the intended device is
reached. This ensures that the signal is received by
its intended device by routing the signal around
obstacles and radio dead spots. The RZP15 Plug-In
Appliance Module is fully compatible with any
Z-wave™ enabled network, regardless of the
manufacturer and can also be used with other
devices displaying the Z-wave™ logo.

Remember to exercise good common sense when
using the Home Automation features of your
Remote – especially when scheduling unattended
devices. There can be some unexpected
consequences if not used with care. For example,
an empty coffee pot can be remotely turned on. If
that should happen, your coffee pot could be
damaged from overheating. If an electric heater is
turned on by remote control while clothing is
draped over it, a fire could result. DO NOT USE the
remote for the control of high power heating
appliances such as portable heaters. This device
will not control lighting that is used with electronic
low-voltage and high frequency power supply
transformers, nor high pressure discharge lamps
(HID lighting). This includes mercury-vapor, sodium
vapor and metal halide lamps.

• Switch ON/OFF
• Works with Z-wave™ compatible Controllers
• Scene Capable
• ON/OFF LED indicates status of load
• Two way communication to provide status

reporting to controllers

• RF reliability
• Ease of installation – No new wiring
• Compatible with other Z-wave™ enabled

devices

NOTE: Use check boxes       when Steps are
completed.

NOTE: In order to use your Vizia™ RF module in a
Z-Wave™ network, it must be Enrolled in the network
using a Primary Programmer/Controller, such as
Leviton’s Cat. No., RZCPG-1LG. Before Enrolling your
module, please refer to the Primary Controller/
Programmer instruction sheet for complete
information. Refer to Step 3 for further details.

•

Locate Load to be controlled by Plug-In Appliance
Module and ensure it is fully operational. Attach
Load plug into Plug-In Appliance Module
receptacle noting proper polarity of blades.

• Plug the Plug-In Appliance Module into wall

receptacle. Verify that receptacle is live. If
controlled by a wall switch, the switch must be
kept ON at all times.

NOTES:
•

Some non-Leviton programmers may be built on
older Z-Wave™ libraries which may require your
module to be replicated in the network instead
of enrolling it in the network. First try to enroll
module in your network. If it is unable to enroll,
refer to the Primary Controller/Programmer
instruction sheet for replicating a device.

When first powering Plug-In Appliance Module,
there is a 30 second enrollmemnt access period
before your device times out.

Within 30 seconds, depress and hold the
programming button located on the front of the
module until the LED beneath the button turns to
solid Amber (approx. 10 seconds).

NOTE: If Plug-In Appliance Module times out,
unplug device from receptacle and plug back in.
The 30 second enrollment access period will
then begin again.

After LED turns solid Amber, release the
button. The LED will start to blink Amber.

The unit is now in the Enrollment/Un-Enrollment
mode.

If necessary to exit the Enrollment/Un-Enrollment
mode, press the programming button.

• Unplug unit when servicing fixture or changing bulbs.

• Save this instruction sheet. It contains important technical data along with testing and troubleshooting

information which will be useful after installation is complete.

C) If using a Leviton Z-wave™ Programmer/

Controller, Cat. No. RZCPG, select the Menu
Screen, then select Network and scroll down
to the Enrollment screen.

D) While standing close to the module, select it

to enroll it in the network.

NOTE: Only one device may be enrolled at
a time. DO NOT put multiple devices into
the  Enrollment mode at any time.

√