Leviton Manufacturing Co. Inc. WSC Benutzerhandbuch

Dip Switches 1-4

Single Pole (One Location)

Cat. No. WSS10, WSC04, WSC15, and WSS0S

Incandescent 800W @ 120V

Ballast 1200VAC @ 120V, 2700VA @ 277V

120-277VAC, 50-60Hz, Motor: 

1

/

4

 HP @ 120V

•  To be installed and/or used in accordance with appropriate electrical codes and regulations.

•  If you are unsure about any part of these instructions, consult a qualified electrician.

•  WSS0S Wireless Remote Switch can be used for additional switches (3-way and 4-way), no wires necessary.

•  Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.

•  Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

•  Recommended minimum wall box depth is 2-1/2”.

Slotted/Phillips Screwdriver 

Electrical Tape 

Pliers 

 

Pencil 

 

 

Cutters 

 

Ruler  

Wire Nuts

Manual ON / Auto ON mode: (factory: manual mode) Occupancy Sensor 

WSC** - Auto mode can be enabled with the use of additional (3) AAA 

batteries or a 5-24VDC connection.

Walk-through: On or Off (can be used only in Auto-ON mode)

Timeout: 2, 10, 20, 30min

Cat. No. WSS10 has a single switch pad that toggles the relay and its 

corresponding load, ON and OFF. If the relay is OFF, the relay will turn 

ON when the push-button is pressed, and remain ON in the presence of 

motion. In the absence of motion, the Sensor Unit will Time-Out and turn 

relay OFF. If in Auto ON/Manual OFF, time delay will start once space is 

vacant.

nOtES:
•  When the lights are on, the Motion Indicator LED will blink red (1 blink 

per minute) every time motion is detected.

•  When the Time-Out expires and the relay turns OFF, a 30 second 

vacancy confirmation exists to turn the relay back ON. 

•  In Manual-ON mode, the button must be pressed to turn the lights ON. 

In the absence of motion, the unit will Time-Out and turn the lights OFF.

lEarn MODE: 
When using the Wireless Occupancy Products together, they must 

LEARN the other devices to perform as desired.
•  WSC04 and WSC15 – Wireless Occupancy Sensor – has learn button   

   on device, under front plastic tab
•  WSS10 – Wireless Momentary Control Switch – use switch pad for      

   learning
•  WSS0S – Wireless Remote Switch – use switch pad for learning

Programming – using Momentary Switch (WSS10) 
•  To enter programming, press and hold the switch pad for 15 seconds
  •  When in programming mode, 
     1 AMBER LED flash, 1 second pause = in programming 
There are 2 modes in programming, LEARN and CLEAR modes. Tap the 

switch pad to select which mode you would like.
  •  1 AMBER LED flash = LEARN mode 
  •  2 AMBER LED flashes = CLEAR mode

Once you have selected the desired programming mode, press and hold 

the pad again for 5 seconds to ENTER the desired mode.  
•  Learn mode:
    •  1 Red flash = no learned devices
    •  1 Green flash = 1 learned devices
    •  2 Green flashes = 2 learned devices
    •  3 Green flashes = 3 learned devices
    •  Etc. (up to 6 devices)
•  On remote switch or occupancy sensor, you must press the switch pad   

   to send a signal for learning. 
    •  AMBER LED on for 2 seconds = acknowledgement, device is  

  

       learned 

    •  GREEN LED on for 2 seconds = device is unlearned

nOtE: Use check boxes        when Steps are completed.

Color change kits are available from Leviton. To change color of frame, 

proceed as follows:

OFF POWEr at circuit breaker or fuse and test that power is 

off before wiring!

Single Pole
1. Line (Hot)

2. Neutral

3. Ground

4. Load 

nOtE: If the wiring in your wall box does not resemble this 

configuration, consult a qualified electrician.

Factory Settings: The sensor is shipped from the factory to work in almost 

all situations, without any adjustments. The factory settings are:  Manual 

mode, when entering the room, the wireless momentary switch will need 

to be turned ON. Wireless occupancy sensor will keep the lights on until 

the room is vacant then turn the lights OFF after timeout period. The PIR 

technology is active. Factory time-out is 10 min.

Time-Outs: The Sensor has four time-out settings: 2, 10, 20, or 30 min.

•  Fixed Time-Out: The value of this time-out is user selected through the 

use of the Dip Switch Settings.

Walk-Through Time Delay: The walk-through feature, which is only active 

in the Auto-On mode, is useful when a room is momentarily occupied. 

With this feature, the Sensor will turn the lights OFF shortly after the 

person leaves the room. The walk-through feature works in the following 

manner: When a person enters the room, the lights will turn ON. If the 

person leaves the room before the walk-through time-out of 2.5 minutes, 

the Sensor will turn the lights OFF within 2.5 minutes of no occupancy 

detected. If the room is occupied for longer than 2.5 minutes, the Sensor 

will enter the Occupied Mode with the time-out duration specified by the 

Dip Switch setting. 

•  Connect (Hot) wire from wall box to black wire on switch.

•  Connect (Load) wire in wall box to blue wire on switch.

•  Connect (Neutral) wire in wall box to white wire on switch.

nOtE: For NO Neutral model, white wire will not be available.

nOtE: For 3-way applications, 4-way and more, use the 

WSS0S Wireless Remote. 

nOtE: To access dip switch settings, lift up the bottom of the 

switch pad. 

1

Auto ON/Manual OFF

Manual ON

2

Walk Through OFF

Walk Through ON

3

X

-

4

X

-

3

X

-

4

-

X

3

-

X

4

X

-

3

-

X

4

-

X