Dayton Industrial Co. Ltd. MULTIW2 Benutzerhandbuch
1
2
3
4
1 - LAP/MEM
Press to set Alarm
Press and hold to delete memory in Training mode
Press to confirm and advance to the next setting
2 - MODE
Press to change modes
Press to exit a menu or page
3 - LIGHT/VIEW
Press and hold for 5 seconds to turn on/off backlight
Press and hold 1 second to turn on/off sound
4 - START/STOP
Press to Start or Stop the timer
Step 1: Set the Time
1. On the Time screen, press and hold the START/STOP
button until the hour setting blinks
TIP: Press and hold the MODE or START/STOP
buttons to scroll quickly through the hours,
minutes, and other Time mode settings.
2. Use the MODE and START/STOP buttons to change
each setting
Biofeedback Accessories
Quick Start User Manual
Introduction
Thank you for purchasing the Sunlighten Biofeedback
Accessories. We are sure you will love these
enhancements to your sauna.
NOTE: Always consult your physician before you
begin or modify any exercise program.
Getting Started
Buttons
3. Press the LAP/MEM button to advance
4. Continue this process to set month, day, year and
12/24 hour mode
Step 2: Set Up Sensors (optional)
Press MODE until the setting page appears. Press
the LAP/MEM button until “Pair New Device” is
displayed. Press START/STOP to initiate pairing, and
wait for on-screen confirmation.
Step 3: Download Free Software
Go to sunlighten.com/biofeedback and follow the
on screen instructions. Use this software to store and
analyze your biometric data.
Step 4: Send Data to Your Computer
NOTE: You must download the software as
instructed in Step 3 so the necessary USB drivers
are installed before connecting the Data Drive to
your computer.
1. Plug the Data Drive into an available USB port on
your computer
Getting Started
2. Bring your Intelli-Watch within range (5m) of your
computer
3. Follow the on-screen instructions
Using the Heart Rate Monitor
The heart rate monitor is on standby and ready to
send data. Wear the heart rate monitor directly on
your skin, just below your breastplate. It should be
snug enough to stay in place during a run.
Getting Started
Getting Started
1. Unsnap one side of the strap from the heart rate monitor
2. Wet the sensors on the back of the heart rate monitor
to create a strong connection between your chest and
the transmitter
3. Wrap the strap around your chest and snap in place
NOTE: When worn properly, the logo should be
right-side up.
4. Bring the Intelli-Watch within range (3m) of the Heart
Rate Monitor
5. Press the MODE button to access Sauna mode
6. If you have erratic heart rate data, you may have to
tighten the strap or warm up for 5-10 minutes. If the
problem persists, you may have to pair the sensors.
See page 13.
Using the Running Sensor
The Running Sensor is on standby and ready to send
data (like the Heart Rate Monitor). When you install or
move the Running Sensor, the LED blinks three times.
1. Press the tabs on the lace clip. Lift and separate the
Running Sensor from the lace clip
2. Loosen your shoe laces slightly
3. Thread the lace clip through 2-3 secure sections of
your shoelaces, allowing enough room at the top to
tie the shoelaces
4. Tie your shoelaces securely to keep the Running
Sensor in place during your workout
5. Snap the Running Sensor into the lace clip and point
it toward the front of your shoe
Getting Started
Time Mode
6. Bring the Intelli-Watch within range (3m) of the
Running Sensor
7. Press the MODE button to access Train mode
8. If the Running Sensor data does not appear, you may
have to pair the sensors. See page 13.
Press the tabs on the front of the lace clip to remove
the Running Sensor.
After 30 minutes of inactivity, the Running Sensor
automatically turns off to conserve the battery (the
LED blinks twice).
Time Mode
Time mode is the default view of the Intelli-Watch.
After 30 minutes of inactivity, the Intelli-Watch
automatically returns to the Time screen. Otherwise,
press the MODE button until the Time screen appears.
Sound
On the Time screen, press and hold view to toggle
Sound mode.
Set the Time
See page 4.
Set the Alarm
1. On the Time page, press LAP/MEM. The Alarm
screen appears
2. Press and hold START/STOP until the hour setting
blinks
3. Use MODE and START/STOP to adjust the hour
TIP: Press and hold the MODE or START/STOP
buttons to scroll quickly through the hours, minutes
and other Time mode settings.
4. Use LAP/MEM to advance
5. When finished, press MODE to resume Alarm
mode
Time Mode
Training Mode
Training mode displays your current workout settings
and data. Press mode until the Training screen appears.
Timed Workout
1. Press START/STOP to begin an active session. Press
LAP/MEM to mark a known distance during your
workout
2. When finished, press START/STOP
NOTE: To pause the active session, press START/
STOP. Press again when you are ready to continue
the session. Your history includes a rest lap that
contains rest time only.
3. To save the workout, press and hold START/STOP
Setting
NOTE: Settings cannot be modified during an
active session in Train mode.
1. Press LAP/MEM to modify user, limits, units or pair a
new accessory
2. On User setting, press START/STOP to create your
name, then press LAP/MEM to advance
NOTE: You can only use START/STOP to set your
name. Hold START/STOP to switch letters quickly.
3. On Limits, press START/STOP to adjust limits and press
LAP/MEM to advance
4. On the Units screen, press START/STOP to adjust
units and use the LAP/MEM button to advance
Training Mode
Speed
1. Press MODE until you find the Speed screen
2. Press LAP/MEM to adjust settings
3. Press START/STOP to toggle between mi/hr and mi/min
4. Press LAP/MEM to advance
5. Press MODE to finish and exit
Result
1. Press MODE until you find the Result screen
2. Press LAP/MEM to toggle through the two sections
of results (TRData and WMData)
3. With TRData selected, press START/STOP and heart
rate (in bpm) will be displayed
4. Press LAP/MEM to toggle through the results
5. When TRData is shown again, press LAP/MEM to
switch to WMData
6. Press START/STOP, then LAP/MEM to see Body Mass
Index (this is only when using the BMI scale accessory)
Training Mode
2
3
4
6
7
8
5
10
11
12
9
Getting Started