Inovonics Wireless Corporation 3B64X9RUX Benutzerhandbuch
8/28/14 06536A_v9 © Inovonics, 2014 - www.inovonics.com
4
Note: IP57 certification was performed by an independent laboratory not
affiliated with UL.
affiliated with UL.
10 End User Recommendations
The pendant transmitter housing is waterproof up to the IP57 standard
when the battery door is properly seated and in the locked position. The
product is designed for incidental/temporary submersion in water, but not
for extended submersion. As such, we offer the following recommendations
to the end user:
when the battery door is properly seated and in the locked position. The
product is designed for incidental/temporary submersion in water, but not
for extended submersion. As such, we offer the following recommendations
to the end user:
* The pendant is able to successfully transmit an alarm or check-in
message when exposed intermittently to water in a shower setting.
However, when the pendant is fully submerged, the water absorbs the radio
signal such that messages may not be reliably detected by the receiver.
message when exposed intermittently to water in a shower setting.
However, when the pendant is fully submerged, the water absorbs the radio
signal such that messages may not be reliably detected by the receiver.
11 Specifications
Dimensions: 1.6" x 1.6" x 0.5" (4 x 4 x 1.25 cm).
Weight: 0.8 oz (23 g) with battery inserted.
Operating temperature: 32 to 140°F (0 to 60°C).
Operating environment: Waterproof.
Estimated battery life: One year (assuming five alarm activations per day
and alarm clearance within ten minutes of alarm activation).
Battery type: Panasonic CR2032.
Power requirement: 3 VDC, 60 mA.
Storage requirement: Ambient conditions of 69 to 73°F (20.5 to 22.8°C).
UL certification for EN1221S-60: UL 2560 (see conditions below).
Weight: 0.8 oz (23 g) with battery inserted.
Operating temperature: 32 to 140°F (0 to 60°C).
Operating environment: Waterproof.
Estimated battery life: One year (assuming five alarm activations per day
and alarm clearance within ten minutes of alarm activation).
Battery type: Panasonic CR2032.
Power requirement: 3 VDC, 60 mA.
Storage requirement: Ambient conditions of 69 to 73°F (20.5 to 22.8°C).
UL certification for EN1221S-60: UL 2560 (see conditions below).
Note: For UL 2560 installations, Inovonics repeaters must have 20 minute
check-in times. Inovonics transmitters must have a minimum of 60 minute
check-in times.
check-in times. Inovonics transmitters must have a minimum of 60 minute
check-in times.
Note: In a UL 2560 installation, the EN1221S-60 senior living pendant may
be used with completed emergency call systems for assisted living and
independent living facilities.
be used with completed emergency call systems for assisted living and
independent living facilities.
For UL 2560 certified system installations, the following Inovonics
EchoStream devices are approved for installation within maximum system
configuration limits defined in section 1.2 of this document:
EchoStream devices are approved for installation within maximum system
configuration limits defined in section 1.2 of this document:
• EN6080 area control gateway or EN6040-T network coordinator with
transformer.
• EN5040-20T high power repeater.
• End devices (transmitters) with a minimum 60-minute check-in
• End devices (transmitters) with a minimum 60-minute check-in
interval, as follows:
- Fundamental devices which are subject to UL 2560 certification
(pendant transmitters and OEM products using the Inovonics RF
module).
module).
- Supplemental devices which are not subject to UL 2560 system
certification but which may be used within a UL 2560 certified system
(e.g. universal transmitters and activity sensors).
(e.g. universal transmitters and activity sensors).
Note: Users that have achieved certification and will install UL 2560
certified systems are responsible for labeling all fundamental devices with
the UL 2560 system certification mark.
certified systems are responsible for labeling all fundamental devices with
the UL 2560 system certification mark.
Compatible receiver for UL 2560 installations with the EN1221S-60:
EN6080
Compatible repeater for UL 2560 installations with the EN1221S-60:
EN5040-20T
EN6080
Compatible repeater for UL 2560 installations with the EN1221S-60:
EN5040-20T
Note: Specifications and data are subject to change without notice.
12 Television and Radio Interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
13 FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product
procedures.
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product
procedures.
14 FCC Part 15 and Industry Canada
Compliance
Compliance
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause
undesired operation of the device. Changes or modifications not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause
undesired operation of the device. Changes or modifications not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Note: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
responsible for compliance could void the user's authority to operate the
equipment.
15 Medical Device Interference
Under FDA and FCC guidelines, the responsibility for verifying continuous
and safe operation of medical devices such as pacemakers and implanted
defibrillators in the presence of electromagnetic interference (EMI) rests
with the manufacturer of the medical device. As such, Inovonics does not
have the authority or specific device knowledge to conduct or interpret
formal tests on their behalf.
Inovonics transmitter devices comply with Part 15 of the FCC Rules and
Industry Canada license-exempt RSS standards.
If you have any concerns about the use of Inovonics transmitter devices in
the presence of medical devices used by a particular resident or patient, we
recommend that you consult with their physician. Another potential source
for answers is the medical device manufacturer, who can provide more
information as to their compliance with federal guidelines and how they
have addressed EMI risk.
and safe operation of medical devices such as pacemakers and implanted
defibrillators in the presence of electromagnetic interference (EMI) rests
with the manufacturer of the medical device. As such, Inovonics does not
have the authority or specific device knowledge to conduct or interpret
formal tests on their behalf.
Inovonics transmitter devices comply with Part 15 of the FCC Rules and
Industry Canada license-exempt RSS standards.
If you have any concerns about the use of Inovonics transmitter devices in
the presence of medical devices used by a particular resident or patient, we
recommend that you consult with their physician. Another potential source
for answers is the medical device manufacturer, who can provide more
information as to their compliance with federal guidelines and how they
have addressed EMI risk.
16 US Patent Numbers
• 7,154,866.
• 7,554,932.
• 7,746,804.
• Other patents pending.
• 7,554,932.
• 7,746,804.
• Other patents pending.
Usage Situation
OK to Use?
Cautions
Shower
Yes*
Do not spray water directly on the
device at distances of less than 12
inches; avoid spraying water at
extremely high pressure.
device at distances of less than 12
inches; avoid spraying water at
extremely high pressure.
Bath
Yes*
Temporary submersion is
permissible. Extended submersion
of the device is not recommended.
permissible. Extended submersion
of the device is not recommended.
Rain
Yes
Avoid extended exposure; wear
the device under a sleeve, shirt, or
jacket
the device under a sleeve, shirt, or
jacket
Water Exercise
No
Do not use the device during these
activities. Please note that the
IP57 rating does not include liquids
with a chemical content such as
chlorine or salt water.
activities. Please note that the
IP57 rating does not include liquids
with a chemical content such as
chlorine or salt water.