Intermec Technologies Corporation SB555 Benutzerhandbuch
578-100-083 Revision C
Page 1 of 2
*578-100-083C*
*578-100-083C*
Compliance Statement Insert
Device Name: Pen Notepad Computer
Model Number: Model 700C (740, 750, & 760 Configurations)
The responsible party for the compliance of this device is:
Intermec Technologies Corporation
6001 36
6001 36
th
Avenue West
Everett, WA 98203 USA
(425) 348-2600
(425) 348-2600
CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can result in
personal injury, fire, or battery explosion.
personal injury, fire, or battery explosion.
This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by
Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that are not approved by
Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the users authority to operate the
equipment.
Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that are not approved by
Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the users authority to operate the
equipment.
FCC Digital Emissions Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the radio or television receiving antenna.
•
Increase the separation between the computer equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
•
Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
WARNING! RF (Radio Frequency) Exposure Regulations for United States and Canada.
RF safety requirements mandate the use of Intermec approved accessories. This device can only be co-located with transmitters approved for the
Intermec 700. Use of antennas and accessories not authorized may void the compliance of this product and may result in RF exposures beyond
the government limits established for this equipment. A 20-cm (8-inch) passing distance must be maintained from any body part of the user or
near by persons and the antennas of the Intermec 700.
RF safety requirements mandate the use of Intermec approved accessories. This device can only be co-located with transmitters approved for the
Intermec 700. Use of antennas and accessories not authorized may void the compliance of this product and may result in RF exposures beyond
the government limits established for this equipment. A 20-cm (8-inch) passing distance must be maintained from any body part of the user or
near by persons and the antennas of the Intermec 700.
LASER COMPLIANCE AND PRECAUTION
The 700C is registered with the CDRH as a Class II Laser Product (CFR 21 Subpart J). This product has a maximum output of 1.0 mW at 630-680 nm.
Warning
There are no user serviceable parts inside the 700C. Use of controls or adjustments, or performance of procedures other than
those specified herein, may result in hazardous laser light exposure of up to 1 mW at 630-680 nm.
There are no user serviceable parts inside the 700C. Use of controls or adjustments, or performance of procedures other than
those specified herein, may result in hazardous laser light exposure of up to 1 mW at 630-680 nm.
Avertissement
Aucune des pièces internes du modèle 700C ne peut être réparée par l’utilisateur.
L’utilisation d’appareils de contrôle et ajustement ainsi que l’exécution de procédures d’utilisation autres que celles qui sont
indiquées dans la présente publication peuvent entraîner une exposition dangereuse à la lumière laser pouvant atteindre
jusqu’à 1 mW à 630-680 nm.
Aucune des pièces internes du modèle 700C ne peut être réparée par l’utilisateur.
L’utilisation d’appareils de contrôle et ajustement ainsi que l’exécution de procédures d’utilisation autres que celles qui sont
indiquées dans la présente publication peuvent entraîner une exposition dangereuse à la lumière laser pouvant atteindre
jusqu’à 1 mW à 630-680 nm.
Note: There are no controls or adjustments provided for routine operation or maintenance of the 700C.
Remarque: Aucun appareil de contrôle ou d’ajustement n’est fourni pour les opérations de routine ou de maintenance de
l’appareil 700C.
l’appareil 700C.
The label shown below is attached on the underside of the 700C devices containing a laser scanner.