Zebra Technologies Corporation MD-QL3021 Benutzerhandbuch
QL 420 User’s Guide
37
After every five
rolls of media
(or more often,
if needed)
rolls of media
(or more often,
if needed)
Use the supplied cleaning pen or 70%
isopropyl alcohol on a cotton swab to
clean the print elements from end to end
(the print elements are located in the thin
gray line on the printhead).
isopropyl alcohol on a cotton swab to
clean the print elements from end to end
(the print elements are located in the thin
gray line on the printhead).
Clean thoroughly with the cleaning pen or
70% isopropyl alcohol and a cotton swab.
70% isopropyl alcohol and a cotton swab.
Units with linerless platens: Rotate media
rollers & clean bearing points only.
rollers & clean bearing points only.
Avoid
use of alcohol on the surface of the
media rollers!
media rollers!
Printhead
(Figure 18)
(Figure 18)
Peel bar
(Figure 18)
(Figure 18)
Clean thoroughly with the cleaning pen or
70% isopropyl alcohol and a cotton swab.
70% isopropyl alcohol and a cotton swab.
Area
Method
Interval
As needed
Media Rollers
(Figure 18)
(Figure 18)
After every five
rolls of media
(or more often,
if needed)
rolls of media
(or more often,
if needed)
Cleaning
CAUTION- Use only cleaning agents specified below. Zebra
Technologies Corporation will not be responsible for damage
caused by any other cleaning materials used on this printer.
Clean the printer with either the cleaning pen supplied with the
printer or a cotton swab saturated with alcohol.
caused by any other cleaning materials used on this printer.
Clean the printer with either the cleaning pen supplied with the
printer or a cotton swab saturated with alcohol.
WARNING: To avoid possible personal injury or damage to
the printer, never insert any pointed or sharp objects into the
printer.
printer.
Platen
Roller
(Figure 18)
Roller
(Figure 18)
Rotate the platen roller and clean it
thoroughly with the cleaning pen or 70%
isopropyl alcohol and a cotton swab.
thoroughly with the cleaning pen or 70%
isopropyl alcohol and a cotton swab.
Units with linerless platens: Rotate
platen & clean bearing points only.
platen & clean bearing points only.
Avoid
use of alcohol on the surface of linerless
platens!
platens!
Tear bar
(Figure 18)
(Figure 18)
Scraper
(Linerless units
only) Figure 18
(Linerless units
only) Figure 18
Clean thoroughly with the cleaning pen or
70% isopropyl alcohol and a cotton swab.
70% isopropyl alcohol and a cotton swab.
Clean thoroughly with the
cleaning pen or 70% isopropyl
alcohol and a cotton swab.
cleaning pen or 70% isopropyl
alcohol and a cotton swab.
Exterior
Water-dampened cloth
Interior
(Figure 18)
(Figure 18)
Brush/air blow. Ensure the Bar Sensor,
Gap Sensor and Label Present Sensor
windows are free of dust.
Gap Sensor and Label Present Sensor
windows are free of dust.
Units with linerless platens:
Clean inside surfaces of edge guides & media
rollers with the supplied cleaning pen or 70%
isopropyl alcohol on a cotton swab.
After every five rolls of media (or more often, if
needed)
Clean inside surfaces of edge guides & media
rollers with the supplied cleaning pen or 70%
isopropyl alcohol on a cotton swab.
After every five rolls of media (or more often, if
needed)
As needed
After every five
rolls of media
(or more often,
if needed)
rolls of media
(or more often,
if needed)
After every five
rolls of media
(or more often,
if needed)
Linerless media
requires more
frequent
cleaning
rolls of media
(or more often,
if needed)
Linerless media
requires more
frequent
cleaning