DEI Headquarters Inc. TX60A Benutzerhandbuch
17
ALARM CONDITION CODES
Use this command to identify which zone is in violation during arming or which generated alarm condition.
Refer to the table of command on page 5 to know which button to press.
Parking lights will flash number of times corresponding to code for protection zone in violation.
If more than one zone is in violation, code for the zone with highest priority is shown (1 = highest priority).
See table of codes below.
Refer to the table of command on page 5 to know which button to press.
Parking lights will flash number of times corresponding to code for protection zone in violation.
If more than one zone is in violation, code for the zone with highest priority is shown (1 = highest priority).
See table of codes below.
Code
Protection Zone
Priority
1
System is armed.
8
2
A door is/was open.
1
3
Hood is/was open.
3
4
Alarm condition is/was detected on shock sensor input.
5
5
Key is/was in the RUN position.
2
6
Alarm condition is/was detected on additional sensor input.
Additional sensor monitors status of __________________________________________________
Additional sensor monitors status of __________________________________________________
4
7
Loss of power (+12V battery supply was removed).
7
8
More than 3 warnings were given within 3 minutes by pre-shock input.
6
CODE LEARNING OF ADDITIONAL TRANSMITTER(S)
Four different remote controls can be programmed for a given vehicle. If a fifth remote is added, the first remote is deleted.
Note: When the first code learning command is sent, all the old codes are cleared out. therefore if you want to add a new
remote, all the old ones must be reprogrammed as well.
One or more remote transmitters can be added. To do this, the programming is accessed as follows:
Note: When the first code learning command is sent, all the old codes are cleared out. therefore if you want to add a new
remote, all the old ones must be reprogrammed as well.
One or more remote transmitters can be added. To do this, the programming is accessed as follows:
Open hood. (Hood switch must be present and operational. – See “Safety checks” on page 17.)
Place key in the ignition and turn to the RUN position
Apply the brakes once
You now have 10 seconds to turn the key from the RUN to the OFF position 3 times.
If this sequence is correctly carried out, the control module flashes parking lights (4 flashes). You may then
proceed to the next step.
proceed to the next step.
Press the
button on the new remote control. When access code of new remote control is memorized,
the control module will confirm with flashing parking lights (1 flash).
Repeat the above procedures for each remote control that has to be programmed (up to 4 remotes).
Apply the brakes.
New remote(s) is (are) now added to the system.
If your vehicle is equipped with a function that automatically sets driver preferences (seat, mirrors, etc.) and the system is
configured to control it, the remote controls programmed in positions 1 and 2 will control the settings for the first driver and
the remote controls programmed in positions 3 and 4 will control the settings for the second driver. If you only have two
remote controls, program the first one twice and the second one twice to occupy the four memory locations of the system.
If your vehicle is equipped with a function that automatically sets driver preferences (seat, mirrors, etc.) and the system is
configured to control it, the remote controls programmed in positions 1 and 2 will control the settings for the first driver and
the remote controls programmed in positions 3 and 4 will control the settings for the second driver. If you only have two
remote controls, program the first one twice and the second one twice to occupy the four memory locations of the system.
SAFETY CHECKS
In order to maintain a high safety standard, proceed with the following checks every month.
HOOD SWITCH
•
Remote start your vehicle.
•
Open hood.
Engine should stop as soon as hood is opened.
If engine does not stop immediately, turn main switch to OFF position and leave it off until situation is rectified. Contact
your service center.
If engine does not stop immediately, turn main switch to OFF position and leave it off until situation is rectified. Contact
your service center.