Lutron Electronics Company Inc 0034 Benutzerhandbuch
R
Job Name:
Job Number:
Model Numbers:
Page
SPecification Submittal
SZ-CI-PRG Programming Control Interface
Description
the Stanza system is an easy-to-install and easy-to-use lighting
control system designed especially for hotel guest rooms and
similar applications. the system consists of wallbox dimmers,
wallbox switches, line-voltage wallbox keypads, low-voltage
interfaces, and lamp socket dimmer/switches. all of these
devices communicate via radio frequency (Rf) within each
individual guest room.
the Stanza programming control interface allows setup,
commissioning, and modification of Stanza systems, and can
also be used to integrate with a Pc or other digital equipment
that supports tcP/iP over 10/100 baset ethernet or RS232
connections.
Features
the Stanza system is an easy-to-install and easy-to-use lighting
control system designed especially for hotel guest rooms and
similar applications. the system consists of wallbox dimmers,
wallbox switches, line-voltage wallbox keypads, low-voltage
interfaces, and lamp socket dimmer/switches. all of these
devices communicate via radio frequency (Rf) within each
individual guest room.
the Stanza programming control interface allows setup,
commissioning, and modification of Stanza systems, and can
also be used to integrate with a Pc or other digital equipment
that supports tcP/iP over 10/100 baset ethernet or RS232
connections.
Features
• integrates a Stanza guest room lighting control system with a
Pc or other digital equipment that supports RS232 or ethernet
tcP/iP communication.
tcP/iP communication.
• Provides a basic serial string command set that allows a Pc to
monitor and control lighting.
• enables use of a Pc to set up and commission Stanza systems.
• at least one SZ-ci-PRG is required per job for commissioning
• at least one SZ-ci-PRG is required per job for commissioning
or system modification. Programmed and commissioned
systems do not require a SZ-ci-PRG to be present for
continued operation.
systems do not require a SZ-ci-PRG to be present for
continued operation.
• Wireless connection allows easy mounting near integration
device.
sz-ci-prg-1 06.06.08
Wireless Control Interfaces
SZ-CI-PRG
Stanza
TM
1
FCC Information
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio or television reception. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the seperation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron
Electronics Co. could void the user’s authority to operate this equipment.
Operation is subject to the following: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio or television reception. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the seperation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron
Electronics Co. could void the user’s authority to operate this equipment.
Operation is subject to the following: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.