Lutron Electronics Company Inc 0110 Benutzerhandbuch

Installation Instructions
Please Read Before Installing

GRAFIK T

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299 USA

Installation

CAUTION: To avoid overheating and possible damage to other equipment, do not use dimmers

to control receptacles, fluorescent lighting fixtures, motor-operated appliances or transformer-
supplied appliances.

2. Install in accordance with all national and local electrical codes.
3. When no “grounding means” exist in wallbox, the NECR allows control without a grounding connection

to be installed as a replacement if 1) a non-metallic, noncombustible faceplate is used with nonmetallic
attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). For this type
of installation, cap or remove the green ground wire on the dimmer/ switch, and only use a LutronR
GraFIk TT wallplate.

4. GraFIk TT controls are not compatible with standard 3-way switches. Use only with companion devices

(GT-aD).

5. Companion devices (GT-aD) cannot be used individually but must be used in conjunction with a GraFIk TT

dimmer/switch in a multi-location application.

6. In any multi-location circuit, use only one GraFIk TT dimmer/switch with up to four companion devices.
7. GraFIk TT dimmer/ switch settings such as “Light Bar Intensity” and “Speaker On/Off” can be modified

using advanced Programming Mode. For instructions and information on how to use advanced
Programming Mode, please see LutronR application Note #534.

Important Notes

120 V~ 60 Hz

Recommended LEDs

CreeR:

CR6 (499485)

Feit Electric:

PAR38/LEDG5

PhilipsR: 9290002330 (426122); 9290002268 (424382); 9290002267 (424374)
SylvaniaR: LED8PAR16/DIM/930/FL36/P/LW
For a complete list of compatible LEDs, please visit:

www.lutron.com/LED

Multi-location – Lamps can be controlled from multiple locations.
One location will be replaced by a GraFIk TT dimmer/ switch and the other location(s) by a
GraFIk TT companion device. The dimmer can be wired on the line-side or the load-side (if
not using neutral wire). Switches and dimmers (if using neutral wire) must be wired on the
line-side.
Dimmer / Switch
Connect the

Green ground wire on the dimmer/ switch to the Green or bare ground wire in

the wallbox (See

Important Notes, number 3 at left).

Connect the

Black

wire on the dimmer / switch to the tagged wire removed from the switch.

Connect the

Red wire on the dimmer / switch to one of the remaining wires.

Connect the

Blue wire on the dimmer / switch to the remaining wire.

Connect the

White wire on the dimmer / switch to the neutral wire in the wallbox.

Neutral wire connection is optional for GraFIk TT dimmers; however, the best dimming
performance will be obtained when the neutral wire is connected. The neutral connection is
required for GraFIk TT switches. always cap the white wire if a neutral wire is not present
in wallbox.
Companion Device
Connect the

Green wire on the companion device to the Green or bare ground wire in the

wallbox (See

Important Notes, number 3 at left).

Connect the

Red wire on the companion device to the tagged wire and to the same color wire

connected to the

Red

wire on the dimmer/switch.

Connect the

Blue wire on the companion device to the remaining wire.

Ganging and Derating

When combining dimmers/ switches in the same wallbox, derating is required. No derating is required for
companion devices.

Designed for use with permanently installed LED, incandescent, tungsten halogen, or magnetic low-voltage

only.

Power Boosters / Load Interfaces: If neutral connection is used, -G25LW and -G5ANSW models can control

power boosters / load interfaces. For a list of compatible power boosters / load interfaces see LutronR P / N

369826, Compatible Power Boosters and Load Interfaces.

Low-Voltage Applications: Use with magnetic (core and coil) low-voltage transformers only. Not recommended

for use with electronic (solid-state) low-voltage transformers but ULR listed for dimmable ELV transformers.

Operation of a low-voltage circuit with lamps inoperative or removed may result in transformer overheating and

premature failure. Lutron strongly recommends the following:

• Do not operate low-voltage circuits without operative lamps in place.

• Replace burned-out lamps as soon as possible.

• Use transformers that incorporate thermal protection or fused transformer primary windings to prevent

transformer failure due to overcurrent.

When using the dimmer / switch to control MLV fixtures, the maximum lamp wattage is determined by the

efficiency of the transformer, with 70%–85% as typical. For actual transformer efficiency, contact either the

fixture or transformer manufacturer. The total VA rating of the transformer(s) shall not exceed the VA rating of

the dimmer / switch.

Includes Mark XT, Tu-WireR, and POWERSENSER.

Not for use with receptacles or appliances (e.g., garbage disposals). See LutronR Application Note #109 for

compatibility with dimmed receptacles.

Control

Load Type

Not Ganged

End of Gang

Middle of Gang

rrT-G25LW

1, 2

HQrT-G25LW

1, 2

LED

250 W

Incandescent / Halogen

600 W

500 W

400 W

MLV

3, 4

400 Va (300 W)

Dimmable Fluorescent

3.3 a (400 Va)

LutronR Hi-lumeR a-Series LTE

LED Driver

3.3 a

10 driver maximum

rrT-G5aNSW

2, 6

HQrT-G5aNSW

2, 6

Lighting

5 a (600 W)

4.2 a (500 W)

3.3 a (400 W)

Fan

3 a (360 W)

Motor

3 a (1/10 HP)

Mixed

3 a (360 W)

Technical Assistance: www.lutron.com | U.S.A.

Canada

Caribbean:

1.800.523.9466 | Mexico: +1.888.235.2910 | Others: +1.610.282.3800 • For warranty details, please visit: www.lutron.com/TechnicalDocumentLibrary/warranty.pdf | For FCC/IC information, please visit: www.lutron.com/fcc-ic

Lutron and Tu-Wire are registered trademarks and FASS and GRAFIK T are trademarks of Lutron Electronics Co., Inc.

NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts.

POWERSENSE is a registered trademark of Osram Sylvania, Inc. |

Mark X is a registered trademark of Philips Lighting Electronics N.A., Inc.

IMPORTANT

Cut the blue wire at the insulation and cap with the yellow

connector.

English

Single-pole –

Switch will be replaced by a GraFIk TT dimmer/ switch.

Connect the

Green ground wire on the dimmer/ switch to the Green or bare ground wire

in the wallbox (See

Important Notes, number 3 at left).

Connect the

Black wire on the dimmer/ switch to one of the wires removed from the

switch. If you had taped together two wires (see step 4), connect both wires to the

Black

wire on the dimmer/ switch and remove the tape.
Connect the

Red wire on the dimmer / switch to the other wire removed from the switch.

Connect the

White wire on the dimmer / switch to the neutral wire in the wallbox.

Neutral wire connection is optional for GraFIk TT dimmers; however, the best dimming
performance will be obtained when the neutral wire is connected. The neutral connection
is required for GraFIk TT switches. always cap the white wire if a neutral wire is not
present in wallbox.

remove wallplate and the switch mounting screws. Leaving all wires attached, carefully
pull the switch out from the wall.

The switch may have two wires attached to the same screw. Tape these two wires
together before disconnecting. Proceed to disconnect the wires from the switch.

remove wallplate from the GraFIk TT dimmer/ switch and any companion device but
leave wallplate adapter connected.

Install GraFIk TT control.

Carefully push wires into the wallbox. Install controls and snap on wallplate.

Turn ON power at circuit breaker.

Turn OFF power at circuit breaker.

If desired, consider adjusting low-end and high-end trim. See

Operation for details.

Troubleshooting

Symptom

Possible Solutions

Two LEDs are blinking.

• Check wiring. If neutral wire is connected, ensure that the Black wire is

connected to Live and the red wire is connected to Load.

• Check wiring. Ensure that the Blue and red wires are connected as

specified in

Installation.

Lamp and light bar LEDs do not turn on.

• Push FaSST up to restore power.

• replace burned out lamp(s).

• Turn ON breaker.

• Check dimmer/ switch wiring (See

Installation).

Unit is unresponsive.

• Cycle power to unit by pulling the FaSST down and back up to fully

restore power.

Lamps turn On and dimmer/ switch

works but companion device does not

work.

•

Ensure that the wire connected to the Blue (or red) wire on the

dimmer/ switch is the same as that connected to the Blue (or red) wire on

the companion device (See

Installation step 6b).

Lamps repeatedly turn On and Off.

• See

Minimum Load and ensure the acceptable minimum load is met.

Lamps flicker or exhibit poor dimming

range.

• Set low-end trim. See

Operation for details.

Wallplate is warm.

• Solid-state dimmers internally dissipate about 1% of the total connected

load. It is normal for dimmers to feel warm to the touch during operation.

Lamps don’t turn On / Off from a keypad.

• Improper programming. Programming must be done through the system

software.

• Out of rF range. reposition to be within 30 ft (9 m) of an rF signal

repeater.

• Wires shorted. Make sure the blue terminal is not grounded or shorted to

any other wires.

• Wiring error. Ensure wiring matches installation instructions and

appropriate wiring diagram.

Minimum Load

For performance or compatibility information, visit

www.lutron.com/LED, which is constantly being updated.

If using neutral wire, the minimum load required is one LED lamp or LutronR Hi-lumeR a-Series LTE LED Driver.

If using neutral wire, the minimum incandescent/halogen load required is 5 W.

Switch

recommended minimum load for the switch is 5 W or one SSL-7a compliant LED lamp. Loads not

meeting this minimum requirement may need a LUT-MLC to function properly.

Dimmer

Load Type

Application

Number of Companion

Devices

LED

1, 2

Incandescent / Halogen

Single-pole

2 LED lamps

40 W

Multi-location

3 LED lamps

80 W

Multi-location

4 LED lamps

120 W

Multi-location

5 LED lamps

160 W

Multi-location

6 LED lamps

200 W

120 V~

60 Hz

Black

Ground

Red

Blue

Green

Neutral

Live

Load

Identify switch type.

Single-pole – The switch will have insulated wires

connected to two screws of the same color plus a

green ground screw.

Multi-location – 3-way switches will have insulated

wires connected to three screws plus a green ground

screw. One of the wires is connected to a screw of

a different color (not green) or labeled COMMON.

Tag this wire.

Tag

Ground

Different-colored screw

Ground

White

WARNING! Shock Hazard. May result in serious injury or death.
Turn off power at circuit breaker before installing the unit.

Connect if

using neutral

wire

IMPORTANT NOTICE: FASST – Front Accessible Service Switch
To replace lamp(s), power may be conveniently removed by pulling the FASST down on the

dimmer/ switch

. After replacing lamp(s), push the FASST back up fully to restore power to the

dimmer/ switch

For any procedure, other than routine lamp replacement, power must be

turned OFF at the main electrical panel.

Operation

Adjust:

(Light Bar)
• Touch to set lamps to

desired level (Dimmer Only).

• Slide to adjust light level

(Dimmer Only).

• Touch anywhere to toggle

load On / Off (Switch Only).

Toggle On / Off:

• Touch to turn Off or to turn

On to previous light level.

• Toggle button is white when

On, orange when Off.

FASST : Front Accessible Service Switch
Note: FASST is not available on

companion devices.

Set High-End Trim:

(Dimmer Only)
1. Press and hold top of light bar

(approximately 6 seconds) until

Toggle button flashes orange.

2. Slide finger on light bar to adjust to

desired brightness.

3. To exit, press and hold the Toggle

button (approximately 6 seconds)

until the Toggle button stops

flashing.

Set Low-End Trim:

(Dimmer Only)
1. Press and hold bottom of light bar

(approximately 6 seconds) until

Toggle button flashes orange.

2. Slide finger on light bar to adjust

to desired brightness.

3. To exit, press and hold the Toggle

button (approximately 6 seconds)

until the Toggle button stops

flashing.

IMPORTANT

Wire connectors provided are for copper wires only. For aluminum

wires, consult an electrician.

Dimmers

LED

MLV

LutronR Hi-lumeR

A-Series LTE LED

Driver

Dimmable

Fluorescent

Incandescent /

Halogen

rrT-G25LW

HQrT-G25LW

250 W

400 Va (300 W)

3.3 a

3.3 a (400 Va)

600 W

Ten (10) driver maximum.

Includes Mark XT, Tu-WireR, and POWERSENSER.

Switches

Lighting

Fan

Motor

Mixed

rrT-G5aNSW

HQrT-G5aNSW

5 a

3 a

3 a (1/10 HP)

3 a

Companion devices
rT-GrDW

For use with rrT- dimmers and switches

HQT-GrDW

For use with HQrT- dimmers and switches

Neutral wire connection is optional for GraFIk TT dimmers; however, the best dimming performance will be

obtained when neutral wire is connected. The neutral connection is required for GraFIk TT switches.

The companion device is wired differently than a standard 3-way switch. Both the red wire and the tagged wire

are connected to the same traveler wire.

P/N 0301759

Rev A

Tag

Live

Dimmer/ Switch Line-Side (Dimmer or Switch)

Neutral

Black

Red

Blue

White

Tag

Blue

Red

Green

Ground

Load

Ground

Black

Red

Blue

White

Green

Blue

Red

Green

Ground

Load

Neutral

Dimmer Load-Side (without neutral wire)

Tag

Neutral

Connect if using neutral wire

Dimmer / Switch

Companion device

Dimmer

Companion device