Digital Security Controls Ltd. 17TL280LER Benutzerhandbuch
LE2080(R) : is an LTE (4G) cellular alarm communicator with HSPA(3G) fallback support that sends
alarm communications to Sur- Gard System I- IP, II, III (SG- DRL2IP, IV (SG- DRL4IP) and 5 (SG-
DRL5IP) central station receivers via an LTE(4)/HSPA(3G) digital cellular network.
TL280LER: Is a dual path LTE (4G) Ethernet alarm communicator that sends alarm communications to
Sur-Gard System I-IP, II, III (SG-DRL3IP, IV (SG-DRL4IP) and 5 (SG-DRL5IP) central station receivers
via Ethernet/Internet or a LTE(4)/HSPA(3G) digital cellular network.
The communicator can be used as either a backup or primary communicator. The communicator sup-
ports Internet Protocol (IP) transmission of panel and communicator events over Ethernet/Internet
and/or HSPA/GPRS.
The cellular performance of the LE2080 (R), TL280LE(R), 3G2080 (R) E or TL2803G (R) E com-
municators depend greatly on the LTE(4G)/HSPA(3G) network coverage in the local area.
Optional antenna kits (GS-15ANTQ, GS-25ANTQ, GS-50ANTQ) are available from DSC to improve sig-
nal strength as required.
NOTE: Prior to installation, confirm with the local service provider that the LTE(4G)/HSPA(3G) network
alarm communications to Sur- Gard System I- IP, II, III (SG- DRL2IP, IV (SG- DRL4IP) and 5 (SG-
DRL5IP) central station receivers via an LTE(4)/HSPA(3G) digital cellular network.
TL280LER: Is a dual path LTE (4G) Ethernet alarm communicator that sends alarm communications to
Sur-Gard System I-IP, II, III (SG-DRL3IP, IV (SG-DRL4IP) and 5 (SG-DRL5IP) central station receivers
via Ethernet/Internet or a LTE(4)/HSPA(3G) digital cellular network.
The communicator can be used as either a backup or primary communicator. The communicator sup-
ports Internet Protocol (IP) transmission of panel and communicator events over Ethernet/Internet
and/or HSPA/GPRS.
The cellular performance of the LE2080 (R), TL280LE(R), 3G2080 (R) E or TL2803G (R) E com-
municators depend greatly on the LTE(4G)/HSPA(3G) network coverage in the local area.
Optional antenna kits (GS-15ANTQ, GS-25ANTQ, GS-50ANTQ) are available from DSC to improve sig-
nal strength as required.
NOTE: Prior to installation, confirm with the local service provider that the LTE(4G)/HSPA(3G) network
is available and active in the area where the communicator will be installed, and that radio signal
strength (CSQ) is adequate.
strength (CSQ) is adequate.
Panel Mounting
The following communicators are compatible with HS2016, HS2016-4, HS2032, HS2064, and HS2128
panels:
panels:
l
3G2080(R)E (HSPA(3G)/GPRS only)
l
TL2803G(R)E (Ethernet/Internet + HSPA(3G)/GPRS dual-path)
l
TL280(R)E (Ethernet/Internet only)
l
LE2080(R) (LTE(4)/HSPA(3G) only)
l
TL280LE(R) (Ethernet/Internet + LTE(4)/HSPA(3G))
Features
l
128-bit AES encryption via cellular and Ethernet/Internet (NIST validation cert. number 2645).
l
Back up or primary cellular alarm communication.
l
Automatically switches to 2G (EDGE/GPRS) if HSPA(3G) service is not available.
l
Ethernet LAN/WAN 10/100 BASE-T (TL2803G(R)E and TL280(R)E only).
l
Fully redundant Ethernet/Internet and cellular dual-path alarm communication (TL2803G(R)E only).
l
Full event reporting to central station.
l
Individual Internet and/or cellular periodic test transmission.
l
Integrated call routing.
l
Visual Verification (Requires Sur-Gard System 5 Receiver)
l
Remote firmware upgrade capability of the communicator and panel firmware via Ethernet and/or cel-
lular.
lular.
l
Panel remote uploading/downloading support via cellular and Ethernet/Internet.
l
PC-LINK connection.
l
Programmable labels.
l
SIA and Contact ID (CID) formats supported.
l
Signal strength and trouble display LEDs.
l
Supervision heartbeats sent via cellular and Ethernet/Internet.
l
Third party integration over cellular/IP. The product supports third party application via serial (R-mod-
els only), cellular and, Ethernet. Refer to third-party application documentation for more information.
els only), cellular and, Ethernet. Refer to third-party application documentation for more information.
Technical Specifications
The TL2803G(R) E is also suitable to be used with a compatible control unit listed for dual line security
transmission when used in conjunction with a DACT or a Public Switched Data Network (PSDN) trans-
mitter, where the PSDN provides the line security and is the primary line. In this mode, alarm signals are
to be sent simultaneously over both communication methods.
transmission when used in conjunction with a DACT or a Public Switched Data Network (PSDN) trans-
mitter, where the PSDN provides the line security and is the primary line. In this mode, alarm signals are
to be sent simultaneously over both communication methods.
6