Digital Security Controls Ltd. 18LE2077 Benutzerhandbuch
38
The communicator status codes will indicate the signal levels with digit 1 and 2, a network sta-
tus with digit 3, and the trouble status with digit 4 and 5 as indicated in table above. For exam-
ple status code 11000F would display following status:
1 – On = Signal indicator 1, is ON
1 – On = Signal indicator 2, is ON
0 – OFF = Network indicator, network is working
00 – TROUBLE INDICATOR = there is no trouble on the communicator.
F – Future code not assigned yet. It is sixth hexadecimal digit. It could be also ‘ - ‘ (dash) instead
of letter F (11000-).
In this example both signal indicators are on indicating that communicator has excellent signal
level; the network indicator is OFF showing that we do not have any network problems and
trouble indicators are both OFF indicating that we don’t have any trouble on the communicator.
tus with digit 3, and the trouble status with digit 4 and 5 as indicated in table above. For exam-
ple status code 11000F would display following status:
1 – On = Signal indicator 1, is ON
1 – On = Signal indicator 2, is ON
0 – OFF = Network indicator, network is working
00 – TROUBLE INDICATOR = there is no trouble on the communicator.
F – Future code not assigned yet. It is sixth hexadecimal digit. It could be also ‘ - ‘ (dash) instead
of letter F (11000-).
In this example both signal indicators are on indicating that communicator has excellent signal
level; the network indicator is OFF showing that we do not have any network problems and
trouble indicators are both OFF indicating that we don’t have any trouble on the communicator.
[985] Radio Initialization Status
The radio initialization status is intended to provide the installer with real-time status of radio
communication. The radio initialization status is displayed in an 8 bit toggle option. Each digit
indicates one task in the radio initialization process as follows:
1. Radio power up
2. Received the SMS from C24
3. Radio reset
4. Radio attached to network
5. Receiver 1 Initialized
6. Receiver 2 Initialized
7. Receiver 3 Initialized
8. Receiver 4 Initialize
The radio initialization status is intended to provide the installer with real-time status of radio
communication. The radio initialization status is displayed in an 8 bit toggle option. Each digit
indicates one task in the radio initialization process as follows:
1. Radio power up
2. Received the SMS from C24
3. Radio reset
4. Radio attached to network
5. Receiver 1 Initialized
6. Receiver 2 Initialized
7. Receiver 3 Initialized
8. Receiver 4 Initialize
The following table shows each digit position in the status code, each digit’s value and its assigned meaning
in the eight-digit code:
For example, the radio initialization status code 12-45--- indicates that Radio has been powered up, it has
received SMS signal from C24, the radio is attached to the network, and Receiver 1 has been initialized.
This code could be followed with...567 if Receivers 2, 3, and 4 are initialized where applicable.
If the radio initialization status code does not indicate any problems, proceed with installation as per this
If the radio initialization status code does not indicate any problems, proceed with installation as per this
manual. If troubles are reported, reset the initialization process. If this action does not fix the problem, refer
to Trouble shooting section in this manual.
Table 18: Trouble Code Indications
Table 17: Radio Initialization Status - 1-8 bits completion
Bit
1
2
3
4
5
6
7
8
Not
Completed
-
-
-
-
-
-
-
-
Completed
1
2
3
4
5
6
7
8
Trouble
Indicator Digit
Possible Causes
Possible Solutions
00
No Trouble
N/A
02
Panel Supervision
Trouble
Check Section [382]Toggle Option[5] is ON (3G/Ethernet Module
Enabled).
Ensure the PC-LINK cable between the Panel and Communicator is con-
nected properly (not reversed) and is securely in place.
04
Lockout Trouble
The SIM card has incorrect PIN programmed or has a PIN that the module
does not recognize. Replace the SIM card.