Everspring Industry Co Ltd TR003-03 Benutzerhandbuch

 
The Indoor Siren is a Z-Wave

TM

 enabled device and is fully compatible with any 

Z-Wave

TM

 enabled network. Z-Wave

TM

 enabled devices displaying the Z-Wave

TM

 

logo can also be used with it regardless of the manufacturer, and ours can also 
be used in other manufacturer’s Z-Wave

TM

 enabled networks.    Inclusion of this 

Indoor Siren on other manufacturer’s Wireless Controller menu allows a full 
alarm condition to be generated once a connected Z-Wave

TM

 enabled device 

has been triggered.    Z-Wave

TM 

enabled devices (refer to nodes) in the system 

also act as repeaters, so as to re-transmit the RF signal to ensure that the signal 
is received by its intended destination by routing the signal around obstacles and 
radio dead spots. 

 

1

 
The Indoor Siren integrates both functions of siren and strobe into one unit.  
Two sound levels, 100dB and 90dB, are available for selection.  When it 
receives a RF command, it will either activate its sounder and flash lights or stop 
these visual and audible alarm indications.         

 
Product Overview 
 

 

 

 

 

 

 

 

1 

LED Indicator

 

5 

Tamper Switch

 

2 

Red Strobe Light

 

6 

Link Key

 

3 

Two-Phase Sound Jumper Link

 

7 

DC Jack

 

4

 Tamper Jumper Link

 

 

 
In the rear casing, there is a link key which is used to carry out inclusion, 

exclusion or reset.    When power is first applied, its orange LED flashes on and 
off alternately and repeatedly at 2-second intervals.  It implies that it has not 
been assigned a node ID and cannot work with Z-Wave enabled devices.    The 
Siren will stay “awake” for 10 minutes when power is first applied to allow time 
for configuration.    Please get familiar with the terms below before starting the 
operations.   
 

Inclusion   

Add a Z-Wave enabled device (e.g. Siren) to Z-Wave network. 

Exclusion   

Delete a Z-Wave enabled device (e.g. Siren) from the network. 

Association 

After inclusion, you have to define the relationship between devices. 
Trough association, device can be assigned as master/slave, and 
specify which slave is going to be controlled by which master. 

Reset 

Restore Siren to factory default. 

 
The table below lists an operation summary of basic Z-Wave functions.    Please 
refer to the instructions for your Z-Wave

TM

 Certificated Primary Controller to 

access the setup function, and to include/exclude/associate devices.    The 
detector executes the function of auto inclusion when… 
 
Auto Inclusion 
 
The function of auto inclusion will be executed as long as the Siren does not 
have node ID and in situations where… 
 
1.  The power is first applied. 
 
2.  The execution of exclusion/reset is successful where the stored node ID is 

cleared. 

 
Note: Auto inclusion timeout is 4 minute during which the node information of 
explorer frame will be emitted once every 5 seconds.  Unlike “inclusion” 
function as shown in the table below, the execution of auto inclusion is free from 
pressing the link key on the Siren. 
 

No node ID 

The Z-Wave Controller does not 
allocate a node ID to the Siren. 

LED: 2-second on, 2-second off; 
Beep: 0.1-second on, 

9.9-second off   

1. Have Z-Wave Controller 

entered inclusion mode. 

Inclusion 

2. Pressing link key 3 times within 

1.5 seconds will enter inclusion 
mode. 

Green LED is on and Siren 
beeps when link key is pressed. 

2

1

1

5

2

Front View

Side View 

4

6

5

6

7

3

3

7

4

Rear View