Rosslare Enterprises Ltd 10F301 Benutzerhandbuch
K5336 4/00
-1-
®
OmniProx™ Reader
Model Series OP10/20/30/40/45
Installation Instructions
WHAT IS THE ADEMCO OmniProx™ READER?
The
OmniProx
Reader is an RFID proximity card
reader to be installed for use with access control
systems.
systems.
These Installation Instructions contain the
following information:
following information:
•
Mounting Instructions
•
Connecting the Reader to the Host
•
Testing and Operation of the Reader
Visit www.omniprox.com for the latest information
and technical support.
and technical support.
HOW TO MOUNT THE READER
Figure 1 shows the front view of the OmniProx.
When mounting, the snap-off cover must be
removed to access the screw holes.
When mounting, the snap-off cover must be
removed to access the screw holes.
Figure 1
Mount the Reader with the appropriate screws (not
supplied) as indicated on the template.
supplied) as indicated on the template.
To mount the Reader, perform the following:
1.
Determine an appropriate mounting position
for the Reader.
for the Reader.
2.
Peel off the back of the self-stick mounting
label template included with the unit and place
at the desired mounting position. (Additional
templates can be downloaded from
www.omniprox.com.)
label template included with the unit and place
at the desired mounting position. (Additional
templates can be downloaded from
www.omniprox.com.)
3.
Using the template as a guide, drill two holes
(hole size is indicated on mounting template)
for mounting the Reader to the surface.
(hole size is indicated on mounting template)
for mounting the Reader to the surface.
4.
Drill a 7/16” (10mm) hole for the cable. If
mounting on metal, place a grommet or
electrical tape around the edge of the hole.
mounting on metal, place a grommet or
electrical tape around the edge of the hole.
5.
Route the interface cable from the Reader
and/or power supply to the host. A linear type
power supply is recommended.
and/or power supply to the host. A linear type
power supply is recommended.
NOTE: The OmniProx Reader can also be mounted using
strong epoxy glue. After application, the Reader should be
firmly held in place until the glue dries.
strong epoxy glue. After application, the Reader should be
firmly held in place until the glue dries.
Check all electrical codes for proper installation.
UL
Card Reader Models OP10/20/30/40/45 are to be
used with control panels whose power supply is UL
listed Class 2 or equivalent.
used with control panels whose power supply is UL
listed Class 2 or equivalent.
HOW TO CONNECT THE READER TO THE HOST
The OmniProx Reader is supplied with an 18-inch
pigtail, having a 6-conductor cable. To connect the
Reader to the Host, perform the following steps:
pigtail, having a 6-conductor cable. To connect the
Reader to the Host, perform the following steps:
1.
Prepare the Reader cable by cutting the cable
jacket back 1¼ inches and strip the wires
jacket back 1¼ inches and strip the wires
½
inch.
2.
Prepare the Host cable by cutting the cable jacket
back 1¼ inches and strip the wires ½ inch.
back 1¼ inches and strip the wires ½ inch.
3.
Splice the Reader pigtail wires to the
corresponding Host wires and cover each
connection (see Figure 2).
corresponding Host wires and cover each
connection (see Figure 2).
4.
If the tamper output is being utilized, connect
the purple wire to the correct input on the host.
the purple wire to the correct input on the host.
5.
Trim and cover all conductors that are not used.
Figure 2 below shows how you should wire the
Reader to the Host.
Reader to the Host.
®
Proximity Reader
FCC ID:
This device complies with part 15 of the FCC
rules. Operation is subject to the folowing two
conditions: (1) This device may not cause
harmful interference. (2) This device must
accept any interference received including
interference that may cause undesired operation.
rules. Operation is subject to the folowing two
conditions: (1) This device may not cause
harmful interference. (2) This device must
accept any interference received including
interference that may cause undesired operation.
®
LISTED
ACCESS CONTROL
SYSTEM UNIT
ACCESSORY
UL 294
SYSTEM UNIT
ACCESSORY
UL 294
S/N:
COLOR
WIEGAND
OUTPUT
Red
DC+ Input
Black
Ground
White
Data 1
Green
Data 0
Brown
LED Control
Purple
Tamper
RED - 4.75-16VDC
BLACK-SHIELD/GND
WHITE-DATA 1
GREEN-DATA0
BROWN-LEDCTL
PURPLE-TAMPER
BLACK-SHIELD/GND
WHITE-DATA 1
GREEN-DATA0
BROWN-LEDCTL
PURPLE-TAMPER
Cable Notes:
1.
The individual wires coming out of the reader are color
coded according to the recommended Wiegand standard.
coded according to the recommended Wiegand standard.
2.
When using a separate power supply for the Reader, this
supply and the Host’s power supply must have a common
ground.
supply and the Host’s power supply must have a common
ground.
3.
The recommended cable is Alpha 1295C which has five
conductors. If the Host is monitoring the Reader’s tamper
output, use six conductor Alpha 1296C. Larger wire
gauges are acceptable. The wire must be stranded with
an overall shield, either foil or braided.
conductors. If the Host is monitoring the Reader’s tamper
output, use six conductor Alpha 1296C. Larger wire
gauges are acceptable. The wire must be stranded with
an overall shield, either foil or braided.
4.
The cable shield wire on the Reader should be attached
to an Earth ground (best) or signal ground connection at
the panel or power supply end of the cable. This
configuration is best for shielding the Reader cable from
external interference.
to an Earth ground (best) or signal ground connection at
the panel or power supply end of the cable. This
configuration is best for shielding the Reader cable from
external interference.
Figure 2
®
SNAP ON/OFF TOP COVER:
Remove to reveal screw holes
for mounting.
Remove to reveal screw holes
for mounting.