Visonic Inc. PWRMAXPLUS Benutzerhandbuch
DE5467U
13
6. SPECIAL FUNCTIONS
6.1 Looking after People Left at Home
An important characteristic of the PowerMax+ is its ability
to function in a mode contrary to the usual behavior of an
alarm system. When the system is in the disarmed state
(or even when armed “HOME” with perimeter protection
only), it can keep track of in-house activity and will report
lack of motion in interior zones if there is no detection of
motion within predetermined time limits.
To use this characteristic, you must ask your installer to
To use this characteristic, you must ask your installer to
program a specific time limit beyond which lack of motion
will be reported as a “not active” alert.
To make things clear, let us assume that an elderly, sick or
To make things clear, let us assume that an elderly, sick or
handicapped person is left unattended in a protected site.
This person, disabled or sick as he may be, will not stay
entirely still for hours. It is only natural that even while
being asleep he will turn over in his bed from time to time.
He might also wander into the kitchen to eat or drink, or to
the bathroom for other necessities. Upon doing so, the
bedroom, bathroom and kitchen motion detectors will
detect his movement.
If, for example, the “lack of motion” time limit is set by your
installer to 6 hours, a virtual 6-hour clock will carry out a 6-
hour “countdown”.
If motion is detected within the 6-hour time frame, the
If, for example, the “lack of motion” time limit is set by your
installer to 6 hours, a virtual 6-hour clock will carry out a 6-
hour “countdown”.
If motion is detected within the 6-hour time frame, the
countdown will restart from the beginning (the virtual 6-hour
clock will be “reset”) and no alert message will be sent out.
If no motion is detected within the 6-hour time frame in any
If no motion is detected within the 6-hour time frame in any
interior zone, the control panel will send a “not-active”
alert message to the central monitoring station or to private
telephones designated by the installer.
IMPORTANT! In addition, you may provide the person
IMPORTANT! In addition, you may provide the person
confined to interiors with a single-button transmitter for
distress situations - see Para. 6.2.
6.2 Emergency Calls for Help
(not to be used in UL-listed systems)
Suppose the disabled person discussed in Para. 6.1 above
has an accident such as falling in the bathtub without being
able to get up. It might take hours before the “No Active”
alert is sent out, but he (or she) must be assisted much
sooner.
Even though the odds for such an accident are not high, it
Even though the odds for such an accident are not high, it
is advisable to provide the disabled person with a
miniature, single-button pendant-type or wristwatch-type
transmitter. Pressing the button on this transmitter will
cause the PowerMax+ to send an “emergency call” to the
central monitoring station or to private telephones
designated by the installer.
To make this possible, ask your installer to define one of
To make this possible, ask your installer to define one of
the 28 zones of the PowerMax+ as an emergency zone.
Then, obtain one of the transmitters listed below and link
this transmitter’s ID code to the emergency zone.
Compatible distress transmitters are (see Fig. 5):
MCT-201 - pendant-type (not listed by UL)
MCT-211 - wristwatch-type (not listed by UL)
MCT-101 - pocket-type (not listed by UL)
Compatible distress transmitters are (see Fig. 5):
MCT-201 - pendant-type (not listed by UL)
MCT-211 - wristwatch-type (not listed by UL)
MCT-101 - pocket-type (not listed by UL)
MCT-201
MCT-211
MCT-101
Figure 5. Single-button Emergency Transmitters
6.3 Remote Control by Telephone
PowerMax+
control
panel
A. Establishing Telephone Communication
You can access the PowerMax+ system from a remote
telephone and perform arming and disarming, activation
and deactivation of electrical devices and the auxiliary
output (PGM), record, playback and erase a voice
message, and investigate the system status. The process
is shown in the next illustration.
1. Dial the PowerMax+ tel. No.
2. Wait for 2-4 rings then hang up.
3. Wait 12-30 sec.
4. Redial PowerMax+ tel. No.
(Sound will be heard for 10
sec.)
Not applicable
when dialing to the
GSM number of the
PowerMax+.
Proceed to step 5.
5. [*} (to stop the sound)
1
6. [user code], [#]
2
7. [Desired command, see next table]
3
Notes
(1) The PowerMax+ responds in a similar way if you just
(1) The PowerMax+ responds in a similar way if you just
dial once and wait until you hear telephone rings (in
USA, for example, 11 rings).
(2) Entering of user code is required once only.
(3) If you wait more that 50 seconds without keying a
(3) If you wait more that 50 seconds without keying a
command, the PowerMax+ will disconnect the line.
B. Executable Commands
Command Keying
Sequence
Disarming
[ ] [1] [#]
Arming Home
[ ] [2] [#]
Arming Home-Instant
[ ] [2]
[
1] [#]
Arming Away
[ ] [3] [#]
Arming Away-Instant
[ ] [3] [1] [#]
Arming Away-Latchkey
[ ] [4] [#]
Arming Away-Instant-Latchkey
[ ] [4]
[
1] [#]
Elect. Devices (No. 01-15) ON
[ ] [5] [device No.] [1]
[
#]
Elect. Devices (No. 01-15) OFF
[ ] [5] [device No.] [0]
[
#]
Activating PGM output
[ ] [5] [0] [0] [1] [#]
Deactivating PGM output
[ ] [5] [0] [0] [0] [#]
Two-way voice communication
(see sub-par. C)
(see sub-par. C)
[ ] [7]
[
#]
Recorded message playback
[ ] [8]
[
1
]
[#]
Recorded message start record
[ ] [8]
[
2
]
[#]
Recorded message stop record
[ ] [8]
[
3
]
[#]
Recorded message erase
message
[ ] [8]
[
4
]
[#]
Investigating system status
[ ] [9] [#]
Quit (end communication)
[ ] [9] [9] [#]
C. Two-Way Voice Communication
(Not to be used in UL-listed systems)
Perform steps 1-6 in par. 6.3A and continue as follows:
1.
1.
[ ] [7]
[
#]
2. Wait for 2 beeps
3.
[3] or [1] or [6] (see below)
The system will start to function in the "LISTEN IN" mode,
letting you hear the sounds within your residence for 50
seconds. If the person under surveillance happens to
speak or cry then, you will hear this. You can switch the
system to Listen-In, Speak Out or Full Duplex, as shown
in the next table.