Climax Technology Co Ltd BX Benutzerhandbuch
1
BX-15ZBS Outdoor Bellbox
Introduction
BX-15ZBS is a ZigBee Outdoor Bellbox. It is capable of raising alarm upon receiving alarm signal from
the coordinator in the ZigBee network when an alarm is activated. During the alarm, the Bellbox will
sound alarm with its built-in siren and also flash the strobe light to attract attention.
The Bellbox utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless
communication protocol that is reliable and has low power consumption and high transmission efficiency.
Based on IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network
and coordinated for data exchange and signal transmission
The Bellbox serves as an end device in the ZigBee network. It can be included in the ZigBee network to
receive alarm signal, but cannot permit any other ZigBee device to join the network through the Bellbox.
the coordinator in the ZigBee network when an alarm is activated. During the alarm, the Bellbox will
sound alarm with its built-in siren and also flash the strobe light to attract attention.
The Bellbox utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless
communication protocol that is reliable and has low power consumption and high transmission efficiency.
Based on IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network
and coordinated for data exchange and signal transmission
The Bellbox serves as an end device in the ZigBee network. It can be included in the ZigBee network to
receive alarm signal, but cannot permit any other ZigBee device to join the network through the Bellbox.
Parts Identification
1. Mounting Holes x 4
2. Function Button
- Press the button once to send a supervision signal.
- Press and hold the button for 10 seconds then release to
- Press and hold the button for 10 seconds then release to
reset the Bellbox.
3. Alarm Length Dip Switches
The Dip Switches contain 4 switches which can be set to
either ON or Off position
either ON or Off position
4. Tamper Switch
The Tamper switch will be activated when the Bellbox is
removed from mounted surface, or it cover opened.
removed from mounted surface, or it cover opened.
5. Battery Compartment
The Bellbox is powered by four 1.5V D-cell alkaline
battery.
battery.
6. LED Strobe Light
The strobe light includes 3 LEDs (From left to right: LED1-> LED2->
LED3)
Refer to below table for LED and siren beep for status indication.
LED3)
Refer to below table for LED and siren beep for status indication.
S
S
i
i
r
r
e
e
n
n
A
A
u
u
d
d
i
i
o
o
S
S
t
t
r
r
o
o
b
b
e
e
l
l
i
i
g
g
h
h
t
t
i
i
n
n
d
d
i
i
c
c
a
a
t
t
i
i
o
o
n
n
Lost connection to current network
LED3 flashes every 20 minutes
Joining ZigBee Network
LED3 flashes twice
Arm 1
beep
All 3 LED flash once
Home
3 beeps
All 3 LED flash once
Disarm 2
beep
Sequentially flash for 1 cycle
Arm (Tamper Fault)
5 beeps
All 3 LED flash 5 times
Home (Tamper Fault)
5 beeps
All 3 LED flash 5 times
Disarm (Tamper Fault)
5 beeps
Sequentially flash for 5 cycles
Arm (Low Battery)
3 beeps
All 3 LED flash 3 times
Home (Low Battery)
3 beeps
All 3 LED flash 3 times
Disarm (Low Battery)
3 beeps
Sequentially flash for 3 cycles
Burglar / Emergency Alarm
Continuous alarm sound
All 3 LED flash continuously
Fire Alarm
Alarm sound for 2 seconds,
followed by a stop of 1
second
followed by a stop of 1
second
All 3 LED flash continuously
ON
OFF