Manualsbrain.com
  1. Handbücher
  2. Marken
  3. Climax Technology Co Ltd
  4. BXZW
  5. Benutzerhandbuch

Climax Technology Co Ltd BXZW Benutzerhandbuch

Download
Seite von 5
 
3
z
z
 
 
R
R
e
e
m
m
o
o
v
v
i
i
n
n
g
g
 
 
D
D
e
e
v
v
i
i
c
c
e
e
 
 
(
(
E
E
x
x
c
c
l
l
u
u
s
s
i
i
o
o
n
n
)
)
 
 
The Bellbox must be removed from existing Z-Wave network before being included into another. 
There are two methods available to exclude a device. 
Exclusion Mode 
z 
Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the 
Z-Wave gateway or control panel manual). 
z 
Within 1.5 seconds, press the Function Button 3 times and the Bellbox will be removed 
from the Z-Wave network. 
Factory Reset 
(Only use factory reset when network Control Panel/Gateway is missing or inoperable). 
z 
Press and hold the Function button of the Smoke Detector for 10 seconds to factory reset 
with all LED flashes once. 
<
<
N
N
O
O
T
T
E
E
>
>
 
 
) 
Factory resetting the Bellbox will restore it to factory default settings (excluded from the 
Z-Wave network). The Z-Wave gateway or control panel will still keep its Z-Wave settings. 
Please refer to the gateway or control panel manual on how to remove the Bellbox’s 
Z-Wave settings. 
z
z
 
 
R
R
a
a
n
n
g
g
e
e
 
 
T
T
e
e
s
s
t
t
 
 
 
To test whether the device is able to communicate with the Z-Wave gateway or control panel: 
z 
Put the gateway / panel into range test mode (Walk Test). 
z 
Press the Function Button on the device. 
z 
The gateway / panel should display if the device is within the operation range (please refer 
to the operation manual of the gateway / panel). 
z 
Z-Wave Sleep Mode 
z 
The Bellbox will enter Z-Wave Sleep mode (to conserve power) after waking up for a short 
period of time (~10 seconds). While in Z-Wave sleep mode, Z-Wave gateways or control 
panels are unable to send commands to the Bellbox. 
z 
To program the Bellbox, please send command(s) to the Bellbox within the wake-up 
period. 
 
Installation 
z
z
 
 
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
 
 
G
G
u
u
i
i
d
d
e
e
l
l
i
i
n
n
e
e
 
 
z 
The Bellbox is designed with a waterproof case to be mounted on 
external wall of your house. 
z 
When mounting the Bellbox, mount as high as possible for its siren 
and strobe light to attract attention when an alarm is activated. 
z 
The Bellbox is designed to be mounted on a flat surface with fixing 
screws and plugs provided.   
z 
The base has 3 mounting holes for you to screw the Bellbox onto 
the wall. 
z
z
 
 
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
 
 
t
t
h
h
e
e
 
 
B
B
e
e
l
l
l
l
b
b
o
o
x
x
 
 
1.  Find the location where the Bellbox is to be mounted. 
2. Remove the Top cover by releasing the bottom screw using a 
Philips screwdriver and pulling the outer case out carefully. 
3.  Hold the Bellbox at the position where it will be mounted. 
4.  Check whether BX has a strong enough signal with the Control 
Panel by putting the Control Panel into Walk Test mode (please 
refer to Control Panel manual). Press the Function Button check 
whether the signal is strong enough (please refer to Control Panel 
manual for signal strength). 
5.  If you are satisfied with the signal strength, remove the Bellbox 
from mounting location. 
6.  Identify the 3 mounting holes, mount and fix the Bellbox on the 
wall using the large screws and wall plugs provided. Secure the 
screws using a Philips screwdriver. Make sure the Tamper Switch 
is fully depressed against the wall.