Climax Technology Co Ltd CTC1052RV Benutzerhandbuch
21
)
If the two way communication is setup
between WTRV/ WTRVS and the
emergency call recipient, the levels of
speaker volume and microphone
sensitivity can not be adjusted.
between WTRV/ WTRVS and the
emergency call recipient, the levels of
speaker volume and microphone
sensitivity can not be adjusted.
4.1.2. Non-Emergency Speech Call
This function is only available when Command
#7 is programmed.
#7 is programmed.
Normal AC Power Supply
Step 1. From Idle mode, press and hold the
RESET button for 3 seconds until
CTC-1052RV emits a short beep.
CTC-1052RV emits a short beep.
Step 2. Release the button and one short
beep will sound. CTC-1052RV dials
the phone number entered in
Command #7.
the phone number entered in
Command #7.
Step 3. If the dialing succeeds, CTC-1052RV
will open a two-way voice
communication between the call
recipient and CTC-1052RV for 30
minutes. The Red button backlight will
illuminate during the communication.
communication between the call
recipient and CTC-1052RV for 30
minutes. The Red button backlight will
illuminate during the communication.
<
<
N
N
O
O
T
T
E
E
>
>
)
If the dialing fails, the Control Panel will
emit 5 beeps, indicating that the Control
Panel may have faults and it is not allowed
to use non-emergency call function.
Please make sure that the settings are
correct . Please note that the call will not
be retried.
emit 5 beeps, indicating that the Control
Panel may have faults and it is not allowed
to use non-emergency call function.
Please make sure that the settings are
correct . Please note that the call will not
be retried.
Step 4. At the last 20 & 10 secs, CTC-1052RV
will emit a beep via the telephone
handset to alert the call recipient.
handset to alert the call recipient.
<
<
N
N
O
O
T
T
E
E
>
>
)
30-minute is allowed for each call and is
inextensible.
inextensible.
Step 5. Press DTMF 9 or Reset button, or
hang up to terminate the call. The Red
button backlight dims and CTC-
1052RV returns to idle mode.
button backlight dims and CTC-
1052RV returns to idle mode.
AC Failure
Step 1. Press and hold the RESET button for
3 seconds until CTC-1052RV emits a
beep every 2 second for 20 secods
until the RED lights on, allowing GSM
module to wake up to dail out.
beep every 2 second for 20 secods
until the RED lights on, allowing GSM
module to wake up to dail out.
<
<
N
N
O
O
T
T
E
E
>
>
)
Before the RED LED lights on, you can
press the Reset button to cancel calling.
press the Reset button to cancel calling.
Step 2. After 20 seconds, if the dialing
succeeds, CTC-1052RV will open a
two-way voice communication
between the call recipient and CTC-
1052RV Pro for 30 minutes. The Red
button backlight will illuminate during
the communication.
two-way voice communication
between the call recipient and CTC-
1052RV Pro for 30 minutes. The Red
button backlight will illuminate during
the communication.
<
<
N
N
O
O
T
T
E
E
>
>
)
If the dialing fails, the Control Panel will
emit 5 beeps, indicating that the Control
Panel may have faults and it is not allowed
to use non-emergency call function.
Please make sure that the settings are
correct . Please note that the call will not
be retried.
emit 5 beeps, indicating that the Control
Panel may have faults and it is not allowed
to use non-emergency call function.
Please make sure that the settings are
correct . Please note that the call will not
be retried.
Step 3. At the last 20 & 10 secs, CTC-1052RV
will emit a beep via the telephone
handset to alert the call recipient.
handset to alert the call recipient.
<
<
N
N
O
O
T
T
E
E
>
>
)
30-minute is allowed for each call and is
inextensible.
inextensible.
Step 4. Press DTMF 9 or Reset button, or
hang up to terminate the call. The Red
button backlight dims and CTC-
1052RV returns to idle mode.
button backlight dims and CTC-
1052RV returns to idle mode.
4.1.3. AC Power Check Up
z If the AC Power failure is detected for 10
seconds or longer, the GREEN LED starts
to flash as a visual warning to the user.
GSM will be then be powered down. Thus,
Remote Programming is unavailable.
GSM will be powered up only at times of
reporting
to flash as a visual warning to the user.
GSM will be then be powered down. Thus,
Remote Programming is unavailable.
GSM will be powered up only at times of
reporting
z Once the AC Power resumes, the GREEN
LED turns steady on again.
z If the AC Power failure lasts for an hour,
CTC-1052RV will send an AC Failure
report to the Monitoring Center.
report to the Monitoring Center.
z After the Power restoration lasts more
than one hour, CTC-1052RV will report AC
Restore to the Monitoring Center.
Restore to the Monitoring Center.
z During the AC Power failure period, Call-
Back function is automatically disabled.