Climax Technology Co Ltd CTC1052RV Benutzerhandbuch

28 

„  If both Digital and Speech Alarm 

reporting are set, the reporting call 
sequence will

 

only be terminated 

once one Digital reporting (any of CID, 
Scancom or Tunstall protocols) and 
one Speech reporting are answered 
successfully. 

„  There is a calling pause between 

each call. For different Tel. Numbers, 
the pause is set as 5 secs, and for 
same Tel. Number, it is set as 62 secs. 

¾ 

Retry Circle: Each Tel. Phone number 
can be retried up to 5 times alternative; 
and max. 15 calls will be retried.  During 
the retry period, the Red LED still stays on 
steadily, while the Red Help Button 
backlight dims. 

¾  In the retry circle, if any digital, voice 

message, or speech reporting fails, CTC-
1052RV Pro makes a 10-min pause, then 
starts another 15-call retry circle, followed 
by another 10-min pause. This cycle 
repeats until all reporting is/are answered 
successfully. 

¾  During the 10-min pause, CTC-1052RV 

Pro returns to normal mode with Red LED 
on:  

‹ 

Press the Green reset button to 
terminate the reporting. 

‹ 

If new event happens, CTC-1052RV 
Pro starts the reporting immediately. 

If an alarm is triggered by Talking Pendant 
(WTRV/ WTRVS): 

„  For Tel number(s) set as Digital 

Method (set by Command #20-
24), the WTRV will wait for 
Central Monitoring Station’s 
DTMF command after digital 
reporting is complete. 

„  For Tel number(s) set as Speech 

Method (set by Command #20-
24), the WTRV/ WTRVS will open 
a remote two-way voice 
communication. 

Put CTC-1052RV in Learning Mode to 
determine the operation range of the devices. 

Step 1.  From Idle mode, press and hold the 

RESET button for 6 seconds. 

Step 2.  Once pressed, a button beep sound 

will be heard. CTC-1052RV will emit 
one short beep at 3 sec., then a 
double beep when it reaches 6 sec. 

Step 3.  Release the button after you heard the 

double beep. Then, a short beep will 
be heard indicating CTC-1052RV is 
now in Learning Mode. The RED 
LED begins to flash. 

Step 4.  Move the device to your desirable 

location in the house, and press the 
TEST button to observe the range for 
its operation. 

Step 5. If CTC-1052RV responds with one 

long beep, then the particular device is 
within the operation range. 

For Talking Pendant WTRV/ WTRVS: 
During Walk Test, when the Pendant 
button is pressed you will hear WTRV/ 
WTRVS emit beep (1s-on / 1s-off). After 
about 3 sec, the Control Panel will emit a 
long beep. About 2 sec later, the Control 
Panel will emit a long beep again, 
indicating the Pendant is within the 
operating range. If you do not hear beeps 
emitted by Control panel, turn the Pedant 
off and repeat the steps mentioned above 
until you hear the Panel beeps. 

Step 6.  To exit Learning Mode, press both 

& HELP buttons 

simultaneously. Or, CTC-1052RV will 
exit Learning mode automatically after 
5 mins of inactivity.  

 

z 

Global Test is used to test if the complete 
system is working properly.  

 

To do the Global Test: 

Step 1. Press the RESET button once. 

2. Within 5 secs, press Pendant 

button.  

Step 3.  CTC-1052RV will emit a short 

beep and report to Monitoring