Climax Technology Co Ltd EMDZW Benutzerhandbuch
1
EMD-1ZW Electricity Power Reader
Introduction
The Energy Meter is a Z-Wave Electricity Power reader designed to be used with a digital watt hour meter
supporting LED pulse output port. The E-meter reads the LED pulse from the watt hour meter and transmits the
data to Z-Wave network coordinator.
The Energy Meter is a Z-Wave enabled device and is fully compatible with any Z-Wave enabled network.
Z-Wave is a wireless communication protocol that uses a low-power RF radio. By taking advantage of the Z-Wave
mesh network, commands can be routed to their destination via intermediary “listening” Z-Wave products.
supporting LED pulse output port. The E-meter reads the LED pulse from the watt hour meter and transmits the
data to Z-Wave network coordinator.
The Energy Meter is a Z-Wave enabled device and is fully compatible with any Z-Wave enabled network.
Z-Wave is a wireless communication protocol that uses a low-power RF radio. By taking advantage of the Z-Wave
mesh network, commands can be routed to their destination via intermediary “listening” Z-Wave products.
Parts Identification
1. LED indicator
The LED indicator lights up in the following conditions:
- Flashes once:
The Energy Meter is transmitting a signal.
- Flashes twice:
The Energy Meter is successfully added into a Z-Wave network.
2. Mounting Holes
3. Battery compartment Cover
3. Battery compartment Cover
Remove the cover to insert 2 Alkaline AA 1.5V batteries to power up
the Energy Meter.
the Energy Meter.
4. LED Sensor Jack
Plug the Sensor into this jack to receive LED signal from the watt hour
meter.
meter.
5. Function Button
- Press the button 3 times within 1.5 seconds to send a learn code.
- Press and hold the button for 10 seconds to factory reset.
- Press and hold the button for 10 seconds to factory reset.
6. IR Sensor
Attach the IR sensor to the watt hour meter, and plug into the IR sensor
Jack to read data from the watt hour meter.
Jack to read data from the watt hour meter.
Features
Battery and Low Battery Detection
The Energy Meter uses 2 Alkaline 1.5V batteries as its power
source, It feature Low Battery Detection function. When the battery
voltage is low, the Energy Meter will transmit Low Battery signal to
notify Z-Wave network coordinator.
The Energy Meter will report its battery percentage to the Control Panel respectively at 100%, 75%, 50%,
25%. If the battery voltage is low (25%), a Low Battery signal will be sent to the Control Panel to notify the
user.
When changing battery, after removing the old batteries, press the function button a couple times to fully
discharge before inserting new batteries
source, It feature Low Battery Detection function. When the battery
voltage is low, the Energy Meter will transmit Low Battery signal to
notify Z-Wave network coordinator.
The Energy Meter will report its battery percentage to the Control Panel respectively at 100%, 75%, 50%,
25%. If the battery voltage is low (25%), a Low Battery signal will be sent to the Control Panel to notify the
user.
When changing battery, after removing the old batteries, press the function button a couple times to fully
discharge before inserting new batteries
Adding Device (Inclusion)
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from
other manufactures and/or other applications. All non-battery operated nodes within the network will act as
repeaters regardless of vendor to increase reliability of the network.
other manufactures and/or other applications. All non-battery operated nodes within the network will act as
repeaters regardless of vendor to increase reliability of the network.
Insert batteries to power on the E-meter.
Put the Z-Wave control panel into Inclusion mode (please refer to the Z-Wave control panel manual).
Within 1.5 seconds, press the Function Button 3 times.
Refer to operation manual of the Z-Wave Gateway or Control Panel to complete the adding process.
If the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the
device is unable to be added into the current Z-Wave Gateway/Control Panel, try removing it first (see
Removing Device
device is unable to be added into the current Z-Wave Gateway/Control Panel, try removing it first (see
Removing Device
).