Climax Technology Co Ltd KPF1 Benutzerhandbuch
4
z
Dual-key Alarm Function
¾
Panic Alarm — Press both 1 and 3 keys to trigger Panic alarm.
¾
Fire Alarm — Press both 4 and 6 keys to trigger Fire alarm.
¾
Medical Alarm — Press both 7 and 9 keys to trigger Medical alarm.
<NOTE>
&
The dual-key alarm function is disabled by default. To enable it, please refer to the Test Mode section.
z
General Operation
¾
If there is Alarm Memory, the Status Blue LED and fault LED will turn ON with 5 beeps (depending on Control
Panel).
Panel).
¾
Enter Test mode — Enter Keypad PIN code and then press ＊ key.
¾
Panic Alarm — Press 1 key + 3 key at the same time. (if the function is enabled)
¾
Fire Alarm — Press 4 key + 6 key at the same time. (if the function is enabled)
¾ Medical
Alarm
—
Press
7 key + 9 key at the same time. (if the function is enabled)
¾
Check Control Panel Status — Normal Mode Press
Χ key.
z
Red LED on: the system is in Away Mode
z
Red LED flash: the system is in Home Mode.
z
Blue LED on: activation of Disarm Mode.
z
Blue flash: failure due to the following reasons:
¾
¾
No response sent by the control panel within 4 seconds.
¾
PIN code was incorrect.
¾ Request
for
Home mode during Arm mode.
¾ Request
for
Force arm.
z
Fault Conditions
When Remote Keypad is under NORMAL OPERATION MODE,
a)
When fault condition exists within Control Panel, if the Keypad is used to arm the panel, the keypad Status Blue and
Fault Amber LED will flash 4 times along with 3 beeps to indicate fault condition.
Fault Amber LED will flash 4 times along with 3 beeps to indicate fault condition.
User can force arm the Control Panel by performing the arm action again.
b)
When the Keypad is used to disarm the panel, the Active Blue LED will turn ON alone with two short beeps indicating
normal operation. At a fault situation, it will emit 5 times and turn on both Status Blue and Fault Amber LED for 5
seconds.
normal operation. At a fault situation, it will emit 5 times and turn on both Status Blue and Fault Amber LED for 5
seconds.
c) If
the Control Panel is under Arm Mode, you CANNOT activate Home mode with Remote keypad. The Status Blue
LED will flash 4 times to indicate transmission error.
d)
If you input incorrect KP Pin code for 4 times, KP will disable the key input for 1 minute, indicated by all LEDs flashing
3 times and 6 beeps. After 1 minute, KP will emit a long beep to indicate that the key function is back to normal.
3 times and 6 beeps. After 1 minute, KP will emit a long beep to indicate that the key function is back to normal.
z
Appendix
If you have forgotten the Pin Code or anything wrong happened in the Remote keypad, you can reset the Remote keypad to
factory default and reinitialize it.
factory default and reinitialize it.
Reset to factory default:
Step 1 Remove the batteries and release the tamper.
Step 2 Press & hold 3 key while inserting the battery.
Step 3 Continue pressing 3 until three short beeps to indicate successful reset.
Step 4 Release 3 key, the reset process is complete.
Step 2 Press & hold 3 key while inserting the battery.
Step 3 Continue pressing 3 until three short beeps to indicate successful reset.
Step 4 Release 3 key, the reset process is complete.
<NOTE>
&
After reset, PIN code reverts to factory default values, 0000. Remote keypad will need a new learn-in process to
start functioning.
start functioning.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.