Climax Technology Co Ltd SRACZW Benutzerhandbuch
1
Wireless AC Powered Indoor Siren (SRAC-23B-ZW)
The Indoor Siren is used to attract attention by sounding an alarm when alarm signal is received from the Z-wave Gateway or
Control Panel.
Control Panel.
1. LED Indicator / Learn Button
-- Send Status signal: Press the button once.
-- Send Learn Code: Press the button 3 times within 1.5 seconds.
-- Factory Reset: Press and hold for ~10 seconds until LED starts to flash (twice).
-- LED flashes twice: When the Siren is plugged into a power socket or when it has just been factory reset.
-- LED flashes once: Learning is successful or when the Siren transmits an AC Fail/Restore signal.
-- Send Learn Code: Press the button 3 times within 1.5 seconds.
-- Factory Reset: Press and hold for ~10 seconds until LED starts to flash (twice).
-- LED flashes twice: When the Siren is plugged into a power socket or when it has just been factory reset.
-- LED flashes once: Learning is successful or when the Siren transmits an AC Fail/Restore signal.
2. Buzzer
-- One long beep: Learning / Inclusion is successful.
-- 2 short beeps: When the Siren is powered on or when the Siren is factory reset.
3. AC
Connect
P
P
o
o
w
w
e
e
r
r
S
S
u
u
p
p
p
p
l
l
y
y
The Siren is powered by AC power; plug the Siren into a power socket to activate the Siren. The Siren will emit 2 short beeps and
enter normal operation mode.
There is a rechargeable battery inside the Siren that serves as a backup in case of a power failure. It takes approximately 72 hours
to fully charge the battery.
During normal operation, AC power is used to power the Siren and at the same time recharge the battery.
enter normal operation mode.
There is a rechargeable battery inside the Siren that serves as a backup in case of a power failure. It takes approximately 72 hours
to fully charge the battery.
During normal operation, AC power is used to power the Siren and at the same time recharge the battery.
L
L
o
o
w
w
B
B
a
a
t
t
t
t
e
e
r
r
y
y
D
D
e
e
t
t
e
e
c
c
t
t
i
i
o
o
n
n
The Siren will report its battery percentage to the Control Panel respectively at 100%, 75%, 50%, 25%. After AC power failure, the
Siren will transmit a Low Battery signal (25%) to The Control Panel when low battery voltage is detected. To restore battery, re-plug
AC power into the power socket. After 12 hours, the Siren will transmit a low battery restored notification to the Control Panel.
Siren will transmit a Low Battery signal (25%) to The Control Panel when low battery voltage is detected. To restore battery, re-plug
AC power into the power socket. After 12 hours, the Siren will transmit a low battery restored notification to the Control Panel.
A
A
C
C
F
F
a
a
i
i
l
l
u
u
r
r
e
e
D
D
e
e
t
t
e
e
c
c
t
t
i
i
o
o
n
n
Whenever the Siren is removed from the power socket, the siren will transmit an AC Failure signal to the Z-wave Gateway or
Control Panel to notify the situation. When the Siren is re-plugged onto the power socket, it will transmit an AC restoration code
(the LED will also flash once).
Control Panel to notify the situation. When the Siren is re-plugged onto the power socket, it will transmit an AC restoration code
(the LED will also flash once).
A
A
d
d
d
d
i
i
n
n
g
g
D
D
e
e
v
v
i
i
c
c
e
e
(
(
I
I
n
n
c
c
l
l
u
u
s
s
i
i
o
o
n
n
)
)
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures
and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase
reliability of the network.
and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase
reliability of the network.
z
Plug the Siren into a power socket.
z
The LED indicator will flash twice.
z
Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or
control panel manual).
control panel manual).