Casablanca Fan Company CASA12T Benutzerhandbuch

Open Battery Door 

by  pressing  down 

on  the  insert  tab 

provided.

Install a “MN21/A23” 

12v  alkaline  batterie 

in the space provided. 

Please  observe  proper 

polarity  placement. 

Replace Battery Door.

You will only have to 
change the dip switch 
settings in the remote 
if you are using more 
than one fan in the same 
area and want to control 
them separately. 

NOTE:  DO  NOT  set  dip  switch  setting  in  the  remote  to ‘000000’,  this  may  cause 

frequency  interference  from  other  Casablanca  Products.All  fans  leave  the  factory  set  to 

“111111” 

To change frequency:
1. 

 Turn power OFF at the circuit breaker or fuse box and at the 

wall switch, for the fan you want to change. 

Open the battery door and remove the battery as shown in 

Figure #1

Change the dip switch settings, assuring that they are 

match the Direct-Touch wall control. See Figure #2.

Re-install the battery with the proper polarity position and 

the battery door.

At the circuit breaker or fuse box and at the wall switch, 

turn the power on for the fan whose frequency you are 
changing.

Within 20 seconds of restoring power to the ceiling fan 

press and hold both the “1” and 

 reverse buttons as 

shown in Figure #3. For 3 seconds, you will hear an audible 
tone indicating the command has been accepted. The Fan 
and Lights will be off. The frequency is now changed.

There are five individual speed settings 
for the fan. Each speed is indicated by the 
number on the controller and an audible tone 
for each speed.

To select the desired fan speed:
Press the number on the controller 
corresponding to the speed desired. 4 is high, 
3 medium, 2 low, 1 ultra-low, and 0 is off.

Note:  It  is  normal  for  the  fan  to 

start in the "High" position from 

"Off" before changing to the selected 

speed.

The direction of airflow can be changed from 
downward to upward or from upward to downward.

To reverse the airflow:
1.  Make sure the fan is on and blades are turning.
2.  Press the 

 reverse button. You will hear a 

series of clicks from the fan as it speeds up 
before coming to a stop and changing direction. 

To turn the lights off and on, press and 

release the 

 button for either the up or 

down lights for less than one second.

To dim either the up or down light, Press 

and hold the 

 button for either the up or 

down light for more than 1 second. The light 
will come on at the last brightness setting 
and increase in brightness until full power is 
reached, then start dimming until the lowest 
setting is reached. This cycle will repeat until 
you release the light button.

Up Light

Down Light

Note: The dimming feature will only 

work as long as the dimming feature 

remains active. See "Operation CFL 

mode".

Your fan has the ability to disable the 
dimming feature to allow the use of CFL 
bulbs. 

To activate CFL mode:
1.  Turn the fan off by using your wall switch.
2.  Allow the fan to remain off for at least 5 seconds.
3.  Turn the fan on by using your wall switch.
4.  Immediately press and hold the "1" and "3" buttons for at least 5 seconds. 

The fans lights will go to 100% brightness and the dimming function will 
be disabled.

To cancel CFL mode:
5.  Turn the fan off by using your wall switch. Allow the fan to remain off for 

at least 5 seconds.

6.  Turn the fan on by using your wall switch.
7.  Immediately press and hold the "2" and "4" buttons for at least 5 seconds. 

The fans lights will dim  to 50% brightness and the dimming function will 
be enabled. Press and hold the light buttons until the desired dimmer 
setting is reached.

Caution: CFL bulbs will not 
function properly when 
dimmed, which may result 
in flickering or reduced bulb 
life.

Programmed into every Direct-Touch fan is an Automatic Demonstration 
Program. It can be used to fully demonstrate 
and test the operation of the fan.

To enter the demonstration program:
1.  Turn the fan off for at least 5 seconds by 

using your wall switch. This will clear the 
fan memory ready for programming.

2.  Turn the fan on by using your wall switch.
3.  Immediately hold the "0" button for at least 5 seconds. 
A multi-tone signal will verify the start of the test program. The fan and lights 
will go through a series of changing fan speeds, reversing the fan operation 
mode, turning off/on, and dimming the lights. 

The complete cycle lasts slightly over one minute. It will continue to repeat 
until the wall switch is turned off for more than five seconds, cancelling the 
program.

Note: With CFL mode active, 
the lights will not dim.

The Safe-Exit Program gives you about thirty 
seconds of light when you turn the lights off, 
enabling you to exit your home before the lights go 
out. To enter the Safe-Exit Program:

1.  Turn the fan off by using your wall switch. 

Allow the fan to remain off for at least 5 
seconds.

2.  Turn the Power on. Immediately press and hold the "4" button for 5 

seconds. When a light button is pressed, an audio tone and series of 
lights blinking will indicate the program is active.

3.  With CFL mode disabled, Pressing a Light Button will cause the lights to 

stay on at 50% brightness for 20 seconds then decrease in intensity for 30 
seconds then turn off.

4.  With CFL mode active, Pressing a Light Button will turn the lights off after 

30 seconds.

5.  To cancel the Safe-Exit Program, turn off power off using your wall switch 

and leave off for five seconds.

The Light-Minder Program automatically turns OFF 
the fan mounted lights after two hours. To enter the 
Light-Minder Program: 

1.  To operate the lights for Light Minder Program 

Turn the fan off by using your wall switch. 
Allow the fan to remain off for at least 5 
seconds.

2.  Turn the Power on. Immediately press and 

hold the "1" button for 5 seconds. A series of 
tones will be heard indicating the command 
has been accepted. Once the lights turn on, 
they will automatically turn off after 2 hours.

3.  If you leave the room and turn OFF the lights, the lights will blink to 

indicate the Light Minder command has been accepted. The lights will 
stay on for 2 hours and then begin to dim. After thirty seconds have 
elapsed, the lights will turn completely off. In CFL Mode, the lights will 
not dim, but shut off after 2 hours.

4.  To cancel the Light Minder Program, turn off power off using your wall 

switch and leave off for five seconds.