Tyco Safety Products/Sensormatic AMS1140 Benutzerhandbuch
Preliminary
AMS-1140 DETECTORS
8200-2684-02, REV. 0
SETUP AND SERVICE GUIDE
1 of 15
AMS-1140 Detectors
Setup and Service Guide
ZA1140-D
Contents
About this Guide .................................................... 1
Detector Service Features ..................................... 1
Circuit Board Pinouts ............................................. 3
Service Procedures ............................................... 3
Field Replaceable Units .................................. 3
Replacing the Secondary Cap Board .............. 3
Replacing the Interconnect Cable ................... 4
Installing the Pedestal Installation Kit .............. 5
Replacing the Alarm Board and Lens ............. 6
Replacing the Fuse ......................................... 7
Inhibiting the Transmitter ................................. 7
Using the Software Configurator ..................... 7
Connecting to AC Power ................................. 8
Tuning the Pedestals ...................................... 9
Troubleshooting ................................................... 10
Checking Detector Operation ........................ 10
Dead system/Low sensitivity ......................... 10
False Alarms ................................................. 11
Understanding Error Codes .......................... 11
Interpreting LED Indicators ........................... 12
Specifications ....................................................... 15
Declarations ......................................................... 15
© 2010 Sensormatic Electronics LLC
About this Guide
This guide explains how to tune, service, and
troubleshoot AMS-1140 detectors. Related
documents are:
troubleshoot AMS-1140 detectors. Related
documents are:
•
Installation Guide, AMS-1140 Detector, 8200-
2684-01
Detector Service Features
AMS-1140 detectors have the following service-
related features:
related features:
•
Power on self-test. Upon power up or
hardware reset, detector software runs a self-
test to ensure it functions.
test to ensure it functions.
•
Diagnostics. You use a laptop computer and
configuration software to set up and configure
the detector, and to determine its operational
status. The detector also has an LED (DS5)
inside the primary pedestal that flashes an error
code if system software should fail.
the detector, and to determine its operational
status. The detector also has an LED (DS5)
inside the primary pedestal that flashes an error
code if system software should fail.
•
Alarm indication. The top cap of the primary
pedestal contains flashing LEDs; the base
cover of the primary pedestal contains a piezo
for an audio alarm. The volume of the audio
alarm is controlled with a pot (RV3) on the main
circuit board in the primary base cover.
cover of the primary pedestal contains a piezo
for an audio alarm. The volume of the audio
alarm is controlled with a pot (RV3) on the main
circuit board in the primary base cover.
•
Transmit inhibit. The base of the primary
pedestal has a hole that provides access to a
transmit-inhibit pushbutton.
transmit-inhibit pushbutton.
•
Tags Too Close indication. If this feature is
enabled by the configurator, the pedestal will
flash a unique alarm pattern when a non-
deactivated label or tag is left in the detection
field of the detector for awhile.
flash a unique alarm pattern when a non-
deactivated label or tag is left in the detection
field of the detector for awhile.
•
Adjacent transmitter interference reduction.
This feature allows service to adjust the Energy
Trim Level to decrease the impact of electronic
noise from nearby anti-theft systems.
Trim Level to decrease the impact of electronic
noise from nearby anti-theft systems.
•
Backfield reduction. If enabled by the
configurator, the detector will reduce the size of
the detection field behind the pedestals.
the detection field behind the pedestals.
•
Simplified design. AMS-1140 detectors are a
simplified design and do not support the
following features or options: people-counting,
relays, auto-phase, wired sync, jammer detect,
auxiliary receivers, remote alarms and external
alarm counters.
following features or options: people-counting,
relays, auto-phase, wired sync, jammer detect,
auxiliary receivers, remote alarms and external
alarm counters.