Digital Monitoring Products Inc PC0133 Benutzerhandbuch

LT

-1156  © 2010 Digital Monitoring P

roducts, Inc.

800-641-4282

www.dmp.com

Made in the USA

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springfield, Missouri 65803-8877

10445

Observe polarity when installing the battery, the positive (+) side up.  Reversing the battery will damage the transmitter.  Use 

a 3V coin cell lithium battery, DMP Model CR2430, or the equivalent battery from a local retail outlet. 
Note: When setting up a wireless system, it is recommended to program zones and connect the receiver before installing 

1. If installed, remove the transmitter housing cover as shown in Figure 1.  

2. If replacing the battery, remove the old battery and dispose of it properly.

3. Place the 3V coin cell lithium battery in the holder positive side up as shown in Figure 2 and press into place.

4. Snap the cover into place, keeping the thinner scooped end of the cover opposite of the battery.

 Risk of fire, explosion, and burns.  Do not recharge, disassemble, heat above 212°F (100°C), or 

 

incinerate.  Properly dispose of unused batteries.

Typical battery life expectancy for DMP Model 1107 wireless transmitters is two years.  DMP wireless equipment uses two-way 

communication to extend battery life.  
The following situations can reduce battery life expectancy:

•  If a receiver is unplugged or not installed.   

: Transmitters continue to send supervision messages until a receiver returns an acknowledgement.   

After an hour the transmitter only attempts a supervision message every 60 minutes.

•  Frequent transmissions, such as a door contact where messages are sent every time the door opens or closes.

•  When installed in extreme hot or cold environments.

The following situation can extend battery life expectancy:

•  Extend transmitter supervision time in panel programming.

•  Infrequent transmission trips, such as a window that rarely sends messages.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  

(1) This device may not cause harmful interference, and  

(2) this device must accept any interference received, including interference that may cause undesired operation.

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons.  It must not 

be co-located or operated in conjunction with any other antenna or transmitter.

Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s 

authority to operate the equipment.

NOTE:  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 

Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation.  

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference will 

not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or 

more of the following measures:

-  Reorient or relocate the receiving antenna.

-  Increase the separation between the equipment and receiver.

-  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-  Consult the dealer or an experienced radio/TV technician for help.

Battery 

Life Expectancy 

2 years (normal operation) 

Type 

 

3V coin cell lithium CR2430

Frequency Range:  

903-927 MHz

Dimensions 

Transmitter  

2 5/8” L x 1” W x 5/16” H

 

Standard Magnet 

2 1/8” L x 3/8” W x 5/16” H 

Commercial Magnet 

2 1/8” L x 3/8” W x 5/16” H

Color  

 

 

White

Housing Material 

 

Flame retardant ABS

1107-HSG-C/10 

 

Chocolate Color Housing-10 pack

U. S. Patent No. 7,239,236

FCC Part 15 Registration ID CCKPC0133
IC Registration ID 5251A-PC0133

Maximum 1/2” 

Mounting 

distance

Standard Magnet Base

Optional Mounting Hole

  

CR2430

Alignment

Notches

Commercial Magnet

Maximum 1/2” 

Mounting 

distance

Optional Mounting Hole

  

CR2430

Alignment

Notches