ademco 8DL-GRIPAIO7 Benutzerhandbuch
Ê800
Ê800
Ê800
Ê800-
-
-
-24121^Š
24121^Š
24121^Š
24121^Š
800-24121 5/18 Rev. A Part 1 (BETA)
ADT7AIO/ADT5AIO Series Installation and Setup Guide
STEP 1 - Installing the Rechargeable Backup Battery and
Power Connector
The control is designed to be placed on a desk/table top with the stand attached or
mounted to a wall using the back plate/cover.
mounted to a wall using the back plate/cover.
1.
Remove the Control’s Case Back.
2. Install the ADTZWM (Wi-Fi
®
and Z-Wave
®
) and/or ADTLTE Communications
modules (if used).
2. Connect the battery connector to the receptacle on the PC board.
3. Insert the Battery Pack into the case.
4. Secure the Battery Pack with the Battery Retainer using the Retaining Screw.
5a. Connect the power cable to the GND and +9V terminals on the AIO and to the +
3. Insert the Battery Pack into the case.
4. Secure the Battery Pack with the Battery Retainer using the Retaining Screw.
5a. Connect the power cable to the GND and +9V terminals on the AIO and to the +
and – terminals on the Power Supply. Refer to Table 1 for wire gauge and length.
Do not apply power at this time. OR
Do not apply power at this time. OR
5b Connect the power supply connector to the receptacle on the AIO. Do not apply
power at this time.
NOTE: If using the optional wall mount configuration, skip to the wall mounting
procedure. If not, complete step 7.
6. Install the Case Back onto the contorl and secure with the screw.
Optional ADTZWM and ADTLTE Communications Module Note: Refer to the Specific
Module Installation section in the online Installation & Reference Guide for instructions on
mounting this module.
Module Installation section in the online Installation & Reference Guide for instructions on
mounting this module.
ADTZWM
MODULE
ADTLTE
MODULE
COVER
SCREW
SCREW
BATTERY
g
ri
p
-0
0
9
-V0
SCREW
TERMINAL BLOCK
POWER
SUPPLY
RECEPTACLE
DETAIL A
BATTERY
CONNECTOR
CONNECTOR
EXT
INT
MACHINE
SCREW
GND
9V
Table 1 – Wiring Guide
Maximum distance between
power supply and control
power supply and control
Wire Gauge
(AWG)
(AWG)
Note: Use UL-listed limited energy
cable
Up to 25 feet (7.62m)
# 22
Up to 45 feet (13.72m)
# 20
Up to 70 feet (21.34m)
# 18
Up to 110 feet (33.53m)
# 16
Mounting the Base to a Wall (Optional)
For wall mounting, perform to the following:
1. Secure the Mounting Plate to the wall with 4 screws.
2. Install the Tamper Screw as shown.
3. Secure the Control to the Mounting Plate by aligning the slots on the Base and
1. Secure the Mounting Plate to the wall with 4 screws.
2. Install the Tamper Screw as shown.
3. Secure the Control to the Mounting Plate by aligning the slots on the Base and
sliding the unit down until locked in position.
4. Secure the Control with the screw.
STEP 2 - Setting up the Communication Links
Note: Do not connect to a receptacle controlled by a switch.
1. Plug the power supply into a 24-hour, 110VAC unswitched outlet. Upon power-
1. Plug the power supply into a 24-hour, 110VAC unswitched outlet. Upon power-
up, the “Please Standby!” will be displayed on the home screen.
2. Connect the Control to the local router.
STEP 3 - Registration Programming and Testing
On a laptop, PC or Smart Device, go to: https://alarmadmin.alarm.com.
IMPORTANT: Once the programming procedure has started and the unit is
powered up, do not remove power or disconnect the battery, nor open the case.
Disconnecting power or activating the tamper switch can cause unpredictable
programming results.
IMPORTANT: Once the programming procedure has started and the unit is
powered up, do not remove power or disconnect the battery, nor open the case.
Disconnecting power or activating the tamper switch can cause unpredictable
programming results.
Radio Activation
Refer to the https://alarmadmin.alarm.com for radio activation.
Testing the System
The following test modes are available:
•
Walk Test
•
Communication Diagnostics
Enter Test mode (Walk Test)
1. After entering Installer Tools Menu Mode, select the “Test” button.
2. Select “Walk Test”. The system enters Walk Test Mode and “Walk Test-Home To
Quit” is displayed
3. Open each protected door and listen for three beeps from the keypad, followed
by the zone’s Voice Descriptor. Identification of each faulted protection point
should appear on the display, and clear when the door is closed.
should appear on the display, and clear when the door is closed.
4. Walk in front of the motion sensor and listen for three beeps and the zone’s voice
descriptor.
5. When testing is complete, select the Home button and enter the Installer Code.
6. Press each key on the wireless key to confirm it performs its assigned function.
6. Press each key on the wireless key to confirm it performs its assigned function.
Specifications
Dimensions:
7.875” W x 5.75” H x 1.0” D
Voltage Input:
P/N 300-10260: White – 9VDC, 2.5A
P/N 300-10260-BK (Black) – 9VDC, 2.5A
P/N 300-10260-CAN (Canada) – 9VDC, 2.5A
P/N 300-10260-BK (Black) – 9VDC, 2.5A
P/N 300-10260-CAN (Canada) – 9VDC, 2.5A
24-Hour Backup Battery:
P/N 300-10186: Rechargeable Backup Battery:
Lithium-ion battery pack rated at 3.6/4.2V, 7500 mAH
Lithium-ion battery pack rated at 3.6/4.2V, 7500 mAH
Communication Formats:
4-Digit Contact ID
Home Health Care Applications
IMPORTANT: In Home Health Care applications [UL1637] you must use pendant
model SiXMEDICAL. The maximum range is 50 ft.
model SiXMEDICAL. The maximum range is 50 ft.
Contacting Technical Support
PLEASE, before you call Technical Support, be sure you:
READ THE INSTRUCTIONS!
READ THE INSTRUCTIONS!
• Determine that the power supply and/or backup battery are supplying proper
voltages.
• Verify your programming information where applicable.
• Note the proper model number of this product, and the version level (if known)
along with any documentation that came with the product.
• Note your ADT customer number and/or company name.
Having this information handy will make it easier for us to serve you quickly and
effectively.
effectively.
For Documentation and Online Support
See Installation and Setup Guide P/N 800-24121 or higher, which can be
ordered by contacting Customer Service at 1-800-238-2727 (1-800-ADT-
ASAP). For technical support please call the ADT Product Support Group at
1-877-748-7628, option 3.
This system must be checked by a qualified technician at least once
every three (3) years
See Installation and Setup Guide P/N 800-24121 or higher, which can be
ordered by contacting Customer Service at 1-800-238-2727 (1-800-ADT-
ASAP). For technical support please call the ADT Product Support Group at
1-877-748-7628, option 3.
This system must be checked by a qualified technician at least once
every three (3) years