Honeywell International Inc. 8DL5805BDV Benutzerhandbuch
- 3 -
NOTE:
If there is a recorded message, you must
playback the message in order to clear the buffer so you
can record a new message.
can record a new message.
To Record a Message
Press the ON, OFF, and 2 buttons in sequence. You
will get an audio announcement stating “Message
Mode.
will get an audio announcement stating “Message
Mode.
Press and release the ON button and begin
speaking into the microphone if you want to record
up to a 20-second message.
speaking into the microphone if you want to record
up to a 20-second message.
Press and release the 2 button to save the recorded
message.
message.
To Playback a Message
Press the ON, OFF, and 2 buttons in sequence. You
will get an audio announcement stating “Message
Mode—Check Message” with the Red LED flashing.
will get an audio announcement stating “Message
Mode—Check Message” with the Red LED flashing.
Press and release the OFF button to playback the
message.
message.
To Activate a Function
To activate a function, press and hold down the
appropriate button until a single beep is heard and the
LED alternately flashes RED and GREEN, and then
release.
appropriate button until a single beep is heard and the
LED alternately flashes RED and GREEN, and then
release.
System Status Indications Table
LED
LED Condition
Speech In TM Mode
Speech In TM2 Mode
System Status
System Armed Away
System Armed Away
Armed Away or Maximum
On Steady
System Armed Stay
System Armed Stay
Armed Stay or Instant
Fire, Fire, Zone (Faulted Zone)
Fire (Voice Descriptor for
Zone)
Zone)
Fire Alarm in progress
Alarm, Alarm, Zone (Faulted Zone)
Alarm (Voice Descriptor for
Zone)
Zone)
Armed, Burglary Alarm in progress
Red
Flashing
Alarm, Alarm, Zone (Faulted Zone)
Alarm (Voice Descriptor for
Zone)
Zone)
Alarm Memory
Green
On Steady
System Disarmed
Ready To Arm
Ready To Arm
System Disarmed
Ready To Arm
Ready To Arm
Disarmed, Ready to Arm
Red &
Green
Green
Flashing Silent
Silent
Indicates
RF
transmission
Silent In
Programming
Mode
In Enable or Disable Encryption Mode
Red &
Green
Green
Alternately Flashing
Silent
In Set Volume Level Mode
AC Loss
AC Loss
AC Loss Condition
Low Battery
Low Battery
Low Battery Condition
Green Flashing
System Disarmed
Not Ready To Arm
Not Ready To Arm
System Disarmed
Not Ready To Arm
Not Ready To Arm
System Not Ready, Zone Faulted
To Request System Status
Because the 5805BDV is a two-way device, users can check
the system status before arming or disarming their system.
To check system status, press and release any button
momentarily.
the system status before arming or disarming their system.
To check system status, press and release any button
momentarily.
A single beep is heard and the LED
alternately flashes RED and GREEN.
After a second or
two, the 5805BDV will display and annunciate the system
status (see the System Status Indications Table). If the
5805BDV does not receive system status information from
the panel for approximately 5 seconds, it will shut itself
down. It will also shut itself down if there is no button
activity within 5 seconds of receiving a status update.
status (see the System Status Indications Table). If the
5805BDV does not receive system status information from
the panel for approximately 5 seconds, it will shut itself
down. It will also shut itself down if there is no button
activity within 5 seconds of receiving a status update.
This device may not receive the system status
properly if it operates within a few feet of the
5881 RF receiver.
properly if it operates within a few feet of the
5881 RF receiver.
Low-Battery Indication
:KHQ WKH XQLW JRHV LQWR D ORZ EDWWHU\ FRQGLWLRQ WKH /('
ZLOO QRW DOWHUQDWHO\ IODVK UHG DQG JUHHQ ZKHQ D EXWWRQ LV
SUHVVHG +RZHYHU WKH /(' ZLOO VWLOO OLJKW WR LQGLFDWH VWDWXV
&KDQJH WKH EDWWHU\ LPPHGLDWHO\ 5HIHU WR LQVWUXFWLRQV LQ §7R
&KDQJH WKH EDWWHU\ LPPHGLDWHO\ 5HIHU WR LQVWUXFWLRQV LQ §7R
,QVWDOO5HSODFH %DWWHU\¨ SDUDJUDSK RQ ILUVW SDJH
Multiple Button Operations
The 5805BDV should NOT be used for 24-hour
silent alarm, as the unit itself is not silent.
silent alarm, as the unit itself is not silent.
Also, it is
recommended that the installer NOT program a one-
button panic.
button panic.
The 5805BDV can generate the same responses as keypad
panic key pairs of [1] + [
panic key pairs of [1] + [
4] and [4] + [#] by depressing ON +
1 and OFF + 2 button pairs, respectively.
You must depress the button pair for at least 2 seconds for
the 5805BDV to recognize the button pair command. These
button pairs allow the user to activate panic, fire, and
medical alarms depending on control panel programming.
the 5805BDV to recognize the button pair command. These
button pairs allow the user to activate panic, fire, and
medical alarms depending on control panel programming.
5805BD
V
-004-V0
OFF
2
ON
1
Specifications
Physical:
Transmitter: 2.8” H x 1.8” W x 0.69” D
Battery:
Maxell AAA or Duracell AAA; Alkaline