Axcera 79XITS-7045 Benutzerhandbuch
WaveCom Electronics Inc
MA4040D Manual; MAN1L0901 REV 13(0104)
Approved: D.P.
23
4.2 MA4011D (and/or MA4012D) Power/Control Module
D
D
I A G R A M
I A G R A M
4.2
4.2
A
A
: R
: R
E A R
E A R
PP
A N E L
A N E L
–MA4011D P
–MA4011D P
O W E R
O W E R
/C
/C
O N T R O L
O N T R O L
M
M
O D U L E
O D U L E
D
D
I A G R A M
I A G R A M
4.2
4.2
BB
: R
: R
E A R
E A R
PP
A N E L
A N E L
–MA4012D P
–MA4012D P
O W E R
O W E R
/C
/C
O N T R O L
O N T R O L
M
M
O D U L E
O D U L E
AC INPUT (Only on MA4011D 110-240 VAC Power/control module, as shown in Diagram 4.2A)
The AC input accepts input voltages from 100 - 240 VAC. The fuse is internal to the IEC holder. If the fuse requires
replacement, ensure the voltage and current rating is correct. The AC power switch may be used for turning the
power on and off to the entire chassis.
The AC input accepts input voltages from 100 - 240 VAC. The fuse is internal to the IEC holder. If the fuse requires
replacement, ensure the voltage and current rating is correct. The AC power switch may be used for turning the
power on and off to the entire chassis.
DC INPUT (Only on MA4012D -48 VDC Power/control module, as shown in Diagram 4.2B)
The DC input accepts voltages from 36 to 60 VDC. There are three terminal strip connectors. Each connector is
labeled. Use care in matching the correct attaching wires to each terminal strip connector. It is recommended that
all three terminal strips, including the chassis ground, be connected prior to system use. The power entry assembly
also contains an integral fuse holder. The fuse rating appears on the label beneath the assembly. If the fuse
requires replacement, ensure the voltage and current rating is correct.
The DC input accepts voltages from 36 to 60 VDC. There are three terminal strip connectors. Each connector is
labeled. Use care in matching the correct attaching wires to each terminal strip connector. It is recommended that
all three terminal strips, including the chassis ground, be connected prior to system use. The power entry assembly
also contains an integral fuse holder. The fuse rating appears on the label beneath the assembly. If the fuse
requires replacement, ensure the voltage and current rating is correct.
ALARM
This connector is reserved for future use.
This connector is reserved for future use.
REMOTE INTERFACE
The Remote Interface connector is a dual RJ45. Both sockets in the connector are identical. The pin-out for the
matching RJ45 plug is shown in the following table and diagram:
The Remote Interface connector is a dual RJ45. Both sockets in the connector are identical. The pin-out for the
matching RJ45 plug is shown in the following table and diagram:
D
D
I A G R A M
I A G R A M
4.2
4.2
C
C
::
D U A L
D U A L
RJ45 I
RJ45 I
N T E R F A C E
N T E R F A C E
C
C
O N N E C T O R
O N N E C T O R
REMOTE
INTERFACE
MADE IN
CANADA
Optional Redundant
PS4011D Power
Supply
100-240VAC
4A MAX.
50-60Hz
FUSE
10A, 250V
PS4011D
REMOTE
INTERFACE
MADE IN
CANADA
CANADA
PS4012D
7A MAX.
36 - 75VDC
48V
Optional Redundant
PS4012D Power
Supply