Sebury Technology Co. Ltd. W3-H Benutzerhandbuch

User  Manual

.8.

.10.

D0

D0

D1

D1

ALARM-

OPEN

D_IN

 DC

/3A

12V

-

-

+

+

-

+

GND

AC&DC

AC&DC

NC

COM

NO

NC

COM NO +12V GND

V+

GND

OPEN

Green

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

Pink

Figure 2

The Reader will transmit the PIN data when it receives the last key (#) press after PIN 
code.
Format:  PIN Code ( any 4-8 digits between 0000-99999999)
Example: PIN code:111111
Press 111111 #, then the output format will be: 0000111111

(

l

   

The Reader will transmit the card data when it reads the Card.
Format: Card Number
(Note: No matter the card is valid or invalid, the data will be transmitted)

l

   

In  this  mode  the  W3-H  supports  a  Wiegand  26-37  bit  input  so  an  external  Wiegand 
device with a 26-37 bit output can be connected to the Wiegand input terminals on the 
W3-H.  Either  an  ID  card  reader  (125KHz)  or  an  IC  card  reader  (13.56MHz)  can  be 
connected to the W3-H. Cards are required to be added at the external reader, except 
where an external HID reader is used, in this case cards can be added at either reader 
or controller. See figure 2.

D0

D1

ALARM-

OPEN

D_IN

GND

AC&DC

AC&DC

NC

COM

NO

V+

V+

GND

GND

D0

D1

Green

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

Pink

Figure 1

To enter the programming mode

*  Master code   #
888888 is the default factory master code 

To exit from the programming mode

*

To change the master code

0    New code    #   New code   #
The master code can be 6 digits long

1    User ID number    #    PIN    # 
The ID number is any number between 
1-2,000. The PIN is any 4-8 digits between 
0000 - 99999999 with the exception of 1234 
which is reserved. Users can be added 
continuously without exiting programming 
mode

To add a PIN user

1   Read Card    #
Cards can be added continuously without 
exiting from programming mode

To add a Card user

To delete a PIN or a Card user

2    User ID number   #  for a PIN user or
2    Read Card   #  for a card user

To unlock the door for a PIN user

To unlock the door for a card user

Enter the  PIN  then press   #

Present the card 

.7.

To change a PIN in card and PIN 
mode (Method 1) 
Note that this is done outside 
programming mode

 

so the user can 

undertake this themselves

To change a PIN in card and PIN 
mode (Method 2) 
Note that this is done out

 

programming mode

 

so the user can 

undertake this themselves

side 

To delete a Card and PIN user just 
delete the card 

*  Read Card  Old PIN #   New PIN #   New PIN #

*   ID number #  Old PIN #   New PIN #  

New PIN #

2  User ID   #

.9.

To set keypad tone

 7   8   #   To disable the keypad tone

 

 

 

 7   9   #   To enable the keypad tone(Factory default) 

To set LED

 7   6   #   To disable the red LED

 

 

 

 

 7   7   #   
 

To enable the red LED(Factory default) 

13. Wiegand Mode Setting

W3-H supports Wiegand 26-37, both input and output. It can be used as a reader or controller.

To set Wiegand format:

9  26-37  #   (Default setting: Wiegand 26)

14.1 W3-H operating as a Wiegand Output Reader
In this mode the W3-H supports a Wiegand 26-37 bit output so the Wiegand data lines 
can be connected to any controller which supports a Wiegand 26-37 bit input. 
See figure 1.

There are 10 groups Duress PIN/card available. When input Duress PIN/card, the door
 will open, at the same time, the output alarm operates.

To add a PIN user

To delete a PIN user

2 

To add a card user

To delete a card user

(The ID number is any number between 2001 2010)

-

Note: 
① User ID number must be any 4digits between 2001 2010
② Duress PIN/card must be unique, should be distinguished from common PIN and card
(When the Duress PIN/card is the same with common PIN and card, they will become invalid 
in Duress, and worked as common user function)

-

(The ID number is any number between 2001-2010)

2 

To reset the Door Forced Open warning

 Read Valid Card or Master Code #

To reset the Door Open Too Long warning

Close the door or  Read Valid Card or  Master Code #

W3-H

 Waterproof 

Keypad/Reader/Controller

Digital Keypad W3-H

Screw Driver

Rubber  Bungs

Self Tapping Screws

Diode

1

    4

4

1

6*27mm, used for fixing

4*28mm, used for fixing

IN4004

User Manual

1

1

Please ensure that all the above contents are correct. If any are missing please notify 
the supplier of the W3-H. 

.1.

Manager Card

2

Manager Add Card & Manager Delete Card

The W3-H is a single door multifunction access control with HID card reader. It is 
suitable for mounting either indoor or outdoor in harsh environments. It is housed in a 
strong, sturdy and vandal proof zinc alloy electroplated case. The electronics are fully 
potted so the W3-H is waterproof and conforms to IP68. 

The W3-H supports up to 2,000 users in either a Card, 4-8 digits PIN, or a Card + PIN 
option and additional 10 groups Duress PIN/Card. The built-in card reader supports HID 
125KHz frequency cards/tags. The W3-H has many extra features including Duress 
PIN/card, block enrollment, Wiegand 26-37 bits interface, and backlight keypad…etc. 

These features make W3-H an ideal choice for door access not only for small shops and 
domestic households but also for commercial and industrial applications such as 
factories, warehouses, laboratories, banks and prisons.

Waterproof, conforms to IP 68 

Strong zinc alloy electroplated anti-vandal case

Full programming from the keypad

2,000 users, supports Card, PIN, Card + PIN 

10 groups Duress PIN/Card

Card interface: HID 125KHz Card

Can be used as a standalone keypad, PIN length 4-8 digits

Pulse mode, Toggle mode

l

   

l

   

l

   

l

   

l

   

l

   

l

   

l

   

.2.

PCB connect diagram

D

0

D

1

A

L

A

R

M

-

O

P

E

N

D

_

IN

G

N

D

A

C

&

D

C

A

C

&

D

C

N

C

C

O

M

N

O

J1

D

0

D

1

A

L

A

R

M

-

O

P

E

N

D

_

IN

G

N

D

A

C

&

D

C

A

C

&

D

C

N

C

C

O

M

N

O

J1

W3-H

l

 

l

 

l

 

l

 

l

 

Remove the back cover from the keypad using the supplied security screwdriver
Drill 4 holes on the wall for the screws and 1 hole for the cable
Fix the back cover firmly on the wall with 4 flat head screws
Thread the cable through the cable hole
Attach the keypad to the back cover

.3.

Operating Voltage

12-24V DC or 1 -18V AC

2

2,000  (Additional10 groups Duress PIN/Card)

Adjustable Door Relay Time

Adjustable Alarm Time

Wiegand Interface

Wiring Connections

Wiegand 26-37 input & output

L128 X W82 X H28mm

600 g

700 g

12 keys: 3 X 4 digits

Operating Humidity 

Dimensions

Net Weight 

Gross Weight

10%-90% RH

1-99 seconds

Electric Lock,  Exit Button, 

 

DOTL, External Alarm

Operating Temperature

-20-50

HID 125KHz card

3-6 cm

Max 2A

Max 20A

User Capacity

Keypad

Card Type

Card Reading Distance

Lock Output Load

 

Alarm Output Load

Active Current

Idle Current

≥65mA
≥35mA

Environment

Conforms to IP68

0-3 minutes

Grey

Yellow

Brown

Red

Black

Blue

Purple

D0

Alarm -

OPEN

D-IN

 12-24V DC or 12-18V AC 

NO

COM

Wiegand Output D0

White

Wiegand Output D1 

Request to Exit Button

Door Contact

 12-24V DC or 12-18V AC Regulated Power Input

 12-24V DC or 12-18V AC Regulated Power Input

Alarm Negative 

Orange

NC

Pink

GND

Green

D1

Relay NO 

Relay COM

Relay NC

W3-H Negative

 12-24V DC or 12-18V AC 

.4.

The relay on board can operate in Pulse Mode (suitable for access control) or Toggle 
Mode (suitable for arming/disarming alarms, switching lights, machines….etc) 

Every time a valid tag/card or PIN is read/input in Pulse Mode, the relay will operate, for 
the pre-set relay pulse time.

Every time a valid tag/card or PIN is read/input in Toggle Mode, the relay changes state, 
which will not turn back until read card or input PIN again.

To reset to factory default, power off, press     , hold it and power on, release it until hear 
two beeps and the LED shines in orange, then read any two HID cards, the LED will turn 
in red, means reset to factory default setting successfully. Of the two HID cards read, the 
first one is Manager Add Card, the second one is Manager Delete Card.

Remarks: Reset to factory default, the user's information is still retained. 

*

The W3-H uses a LDR (light dependent resistor) as an anti tamper alarm. If the keypad 
is removed from the cover then the tamper alarm will operate. 

.5.

.6.

Power on

Operation successful

Operation failed

Enter into programming mode

-

-

-

Bright

Bright

Bright

-

-

Bright

-

-

-

Short Ring

-

Short Ring

Short Ring

3 Short Ring

Short Ring

-

Short Ring

Press keypad

-

-

Stand by

In the programming mode

Exit from the programming mode

Open the door

Bright

-

Bright

Alarm

-

Alarm

Bright

-

Short Ring

-

-

-

-

-

Bright

-

-

-

-

To exit from the programming mode

To change the master code

set valid card only users
set valid card and PIN users
set valid card or PIN users

*     Master code     # 

888888 is the default factory master code

To enter the programming mode

*     

0   New code    #   New code    #

The master code is any 6 digits

3 0

#

3 1

#

3 2

#

Entry by either Card or PIN (default)

Entry by Card only

Entry by Card and PIN together

To add a PIN user

 1  User ID number   #   PIN   # 
The ID number is any number between 1- 
2000. The PIN is any 4-8 digits between 0000 
-99999999 with the exception of 1234 which 
is reserved. Users can be added

 

continuously 

without exiting from

 

programming

 

mode

 

as

 

follows:
 1   User ID No 1   #   PIN   #  User ID No 2   #   PIN   #

To delete a PIN user

 2  User ID number  #  

Users  can  be  deleted  continuously  without 
exiting programming mode

To delete card user by card 

Note users can be deleted 
continuously without exiting 
from programming mode

2   Read Card    #  

To delete a card user by user ID

 

This option can be used when

 

a

 

user has lost their

 

card

2   User ID   #  

To add a card user (Method 3)

Add a series cards users - Block
Enrollment

5  ID number   #  The 1st Card number   # 
Card quantity   # 
Note that cards must be consecutive, and card
quantity is between 1-2000
Maximum 2,000 cards can be enrolled at a 
stretch within 2 minutes

To delete   card user by card number 

Users can be deleted 
continuously without exiting 
from programming mode

a

2   Card number   #  

To Add a card and PIN user

(The PIN is any 4-8 digits between 
0000 - 99999999 with the 
exception of 1234 which is 
reserved)

Add the card as for a card user 

Press     to exit from the

Then allocate the card a PIN as

 

follows:

    Read Card    1234 #   PIN #   PIN #

*  

*

To change the PIN of a PIN user 

To add a card user (Method 1)
This is a fastest way to add cards
 using ID number auto generation

To add a card user (Method 2)
T h i s i s t h e o p t i o n a l w a y t o a d d 
cards using User ID Allocation. 
In this method a User ID is allocated
to a card. Only one user ID can be
allocated to a single card

       ID number #    Old PIN #    New PIN #   
  New PIN #

*

1    ID number   #   Card   #

1   Read Card    #  

Cards can be added continuously without exiting 
programming mode

l

   

l

   

l

   

l

   

Wiegand 26-37 input & output

One programmable relay output, NO, NC, COM

Adjustable door output time, alarm time, door open time 

Card block enrollment

l

   

l

   

l

   

l

   

l

   

l

   

l

   

With Manager Cards for adding or deleting card user easily

Backlight keypad

Built in light dependent resistor (LDR) for anti tamper

Built in buzzer

Red, Yellow and Green LED display the working status

12-24V DC or 12-18V AC

Two-year warranty

W3-H

D0

D1

ALARM-

OPEN

D_IN

 DC

/3A

12V

-

+

Wiegand D0

Wiegand D1

GND

AC&DC

AC&DC

NC

COM

NO

NC

COM

NO

+12V GND OPEN

Green

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

Pink

Door 

detecting switch

+

-

+

-

Fail-secure lock

Alarm“-”

To add Card User by Manager Add 
Card

To delete Card User by Manager 
Delete Card

Manager add card  Read User card 
Manager add card  
Cards can be added continuously

Manager delete card  Read User Card  
Manager delete card
Cards can be deleted continuously

For a PIN user

Enter the PIN  then press #

For a card user

Read card

For a card and PIN user

Read card then enter PIN #

To Add and Delete a card user

To delete ALL users 
Note that this is a dangerous option
so use with care

The operating is the same as adding and deleting 
a card user in 3   2   #

2   0000   #

D0

D1

ALARM-

OPEN

D_IN

W3-H

-

+

Green

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

GND

AC&DC

AC&DC

NC

COM

NO

Pink

-

+

In

4

0

0

4

Power“+”

Electric bolt：

NC

Electric strike：

NO

Power“+”

Alarm  -

“ ”

Door 

detecting switch

12-24V

 DC or 

12-18V

 AC/3A

Notes:
Connect the negative pole of the lock to NC is for Fail safe lock.
Connect the negative pole of the lock to NO is for Fail-secure lock. 

Keypad Lockout

Alarm Output

Normal status: No keypad lockout
or alarm

 7   0   #  

 

(Factory default)

 7   1   # 

 7   2   # 

Keypad  Lockout  &  Alarm  Output  options.  If  there  are  10  invalid  cards  or  10 
incorrect  PIN  numbers  in  a  10  minute  period  either  the  keypad  will  lockout  for  10 
minutes  or  the  alarm  will  operate  for  10  minutes,  depending  on  the  option  selected 
below.

To set the alarm output time (0-3 
minutes). Factory default is 1 minute

9   0-3   #

To disable door open detection

Door Open Detection 
Door Open Too Long (DOTL) warning. When used with an optional magnetic contact 
or built-in magnetic contact of the lock, if the door is opened normally, but not closed 
after 1 minute, the inside buzzer will beep automatically to remind people to close the 
door and continue for 1 minute before switching off automatically.

Door Forced Open warning. When used with an optional magnetic contact or built-in 
magnetic contact of the lock, if the door is open by 

, or if the door is opened after 

20 seconds of the electro-mechanical lock not closed properly, the inside buzzer and 
alarm output will both operate. The Alarm Output time is adjustable between 0-3 
minutes with the default being 1 minute.

 

force

To enable door open detection

 6   1   # 

11.3  

Alarm, Sound and Light Settings

To set keypad backlight

 7   4   #   
 7   5   #   

To enable keypad backlight(Factory default) 

Toggle mode

Toggle mode

4   0   #

Pulse mode
(Door relay time setting)

Pulse mode(Factory default)

4   1-99   #

The door relay time is between 1-99 seconds,
the factory default setting is 5 seconds.

 6   0   #   (Factory default )

To disable keypad backlight