Futaba Corporation CGY760R-24G Benutzerhandbuch
108
FUTABA CORPORATION
oak kandakajicho 8F 3-4 Kandakajicho, Chiyoda-ku, Tokyo 101-0045, Japan
TEL: +81-3-4316-4820, FAX: +81-3-4316-4823
©FUTABA CORPORATION 2018, 03 (1)
19.3 mm
4-M3
7.0 mm
21.6 mm
S
PECIFICATIONS
CGY760R
Control System: Digital advanced control
Angular Velocity Range: ±1,000 Degrees Per Second (Gyro)
Sensor: Micro Electromechanical Systems (MEMS) Gyro
Hall effect sensor
Governor Resolution: 0.1Hz (6rpm) (Engine RPM)
RPM Accuracy: 1%
Head Speed Range: 700-4,000rpm
Selectable Servo Frame: 70Hz, 280Hz and 560Hz (Rudder Gyro only) Rate
Center Pulse Width: 1520µS (70Hz & 280Hz) 760μs (560Hz)
Receiving system: FASSTest-2.4GHz (18CH/12CH mode )/T-FHSS-2.4GHz
S.BUS2 / S.BUS Port and 6 Channels for Conventional System
Anntena: Dual antenna diversity
Rated voltage: 3.7V to 7.4V DC* (Operating Voltage:3.5V to 8.4V)
Current Drain: 85mA (When receiving, no servo, no RPM sensor)
Operating Temperature: 14°F to 113°F (-10°C to +45°C)
Size (CGY760R) : 1.055in [26.8mm](W)/1.476in [37.5mm](L)/0.63in [16mm](H)
Size (Revolution sensor) : 0.827in [21mm](W)/0.63in [16mm](L)/0.39in [10mm](H)
Weight (CGY760R) : 0.713oz [20.2g]
Weight(RPM sensor): 0.141oz [4g]
* The operating voltage shown only applies to the CGY760R and GBP-1. Always
verify that your receiver, servos, tail rotor servo, switch and any other electronic com-
ponents used in your installation are capable of operating at the voltage you plan to
use.
verify that your receiver, servos, tail rotor servo, switch and any other electronic com-
ponents used in your installation are capable of operating at the voltage you plan to
use.
GBP-1
Rated voltage: 3.7V to 7.4V DC* (Operating Voltage:3.5V to 8.4V)
Current Drain: 62mA
Operating Temperature: 14°F to 113°F (-10°C to +45°C)
Display: 128 x 64 dot graphics
Size : 2.126in [54mm](W)/3.543in [90mm](L)/0.6102in [15.5mm](H)
Weight(RPM sensor): 1.88oz [53.3g]
WARNING
When installing with screws, take countermeasures against vibra-
tion damping of the machine and make the state with less vibration.
*Please do not mounting with machine screws with vibration, please mounting with a
dedicated mounting pad.
dedicated mounting pad.
M
OUNTING
O
F
CGY760R W
ITH
S
CREWS
Drill holes in the plate
Refer to the figure below and
drill holes to attach to the plate.
Screw size for fi xing
The effective length of the fixing screw
hole of the CGY760R main unit is 7mm.
Use the M3 screw whose length is less
than the plate thickness plus 7mm.
Mounting
Fix it with M3 screw from the bottom of the
plate as shown on the right. Please refer
to the above explanation for the length.
to the above explanation for the length.
NOTE:
*Please take measures to prevent loose-
ness so that the screw does not become
loose during l ight.
loose during l ight.
*CGY 760R main body Since the case is
made of aluminum, be careful not to over-
tighten the screw.
tighten the screw.