Authinx Inc. CR14A Benutzerhandbuch

To clear all stored positions: Press and hold Center then flip
the switch at the bottom to Program and back.

Pan ‘n Tilt Remote

For use with X10 wireless cameras

Model CM14A

CM14A-8/01

1. Install 4 AAA alkaline batteries (sold separately) in the

remote’s battery compartment.

2. Use a dime to set the Housecode dial to match the cameras,

and transceiver you want to use the remote with.

3. Plug in an X10 Transceiver (RR501 or TM751, sold separately).

Set Housecode to match remote. Fully extend the antenna.

4. To control up to 4 Cameras, attach each one to a ZC15A Pan

and Tilt base (sold separately), plug each ZC15A into its own
Addressable Power Supply, and set each power supply to
the same Housecode you used in steps 2 and 3. Set each
power supply to a unique number between 1 and 4. Pressing
any Camera button (C1, C2, C3, or C4) turns on that camera (1,
2, 3, or 4) and turns the others (in the group) off.  Then, each
press of either the        or         button turns on the next or
previous camera in the group of 4 while turning the current
camera off. (You set all cameras to the same channel as the
Video Receiver connected to your TV (Channel A, B, C, D).

5. After you press the "C" button to turn on a camera, pressing

a left or right BLUE button at the top “pans” the camera left or
right. Pressing a BLUE up or down button “tilts” the camera
up or down.

6. To make buttons C1 thru C4 control cameras 5-8 (instead of 1

thru 4) press (and hold) the C2 button then flip the switch at
the bottom from Normal to Program and back. Buttons C1, C2,
C3, and C4 now control cameras set to 5, 6, 7, and 8.

7. Pressing C3 in step 6 sets buttons C1, C2, C3, and C4 to

control cameras set to 9, 10, 11, and 12.

8. Pressing C4 in step 6 sets buttons C1, C2, C3, and C4 to

control cameras set to 13, 14, 15, and 16.

Buttons P1 thru P4 are used to store 4 position settings for
each of the 4 cameras controlled by buttons C1 thru C4.
1. To store the first position for the camera controlled by C1,

press C1.

2. Press the blue buttons to scan to the position you want.
3. Press and hold P1, then flip the switch at the bottom from

Normal to Program and back, to store that position under P1.

4. Repeat steps 2 and 3, pressing P2 to store another position

under P2.

5. Repeat for P3, and P4.
Repeat steps 1 thru 4 to store 4 positions for C2, C3, and C4.
Press the “C” button for any camera, following by any “P”
button to move to the position stored under that button for
that camera.

Press the “C” button then Sweep to sweep through all 4
positions stored for that camera.

Press the “C” button then Center to center the position for
that camera.

The CR14A Remote lets you turn on any of 4 cameras or scan each of them in turn (forward or backward) so as to display the image from
each camera in turn on your TV. If you purchase a Camera Pan and Tilt base (model ZC15A) for each camera, you can also use the remote
to move the position of the camera from left to right (Pan) and up and down (Tilt).  The Remote sends Wireless Radio Frequency (RF)
signals to an X10 Transceiver (RR501 or TM751). The Transceiver then passes the signals onto your house wiring to control Wireless
Cameras around your home.  You connect each camera (up to 4) to a ZC15A base and plug each ZC15A into Addressable Power Supplies
each set to a different number. The CR14A normally controls Cameras set to Unit Codes 1, 2, 3, 4. But you can set it to control cameras set
to 5, 6, 7, 8, or 9, 10, 11, 12, or 13, 14, 15, 16.

A

C

E

G

I

K

M

O

.

.

.

.

.

.

.

.

Set to the same letter as
the TM751 and cameras.

Scans forward or backward
thru cameras controlled by
C1 thru C4.

“Pans” left
and right.

“Tilts” up
and down.

Write
locations
of cameras
here.

Controls 4
cameras.

Stores the
positions
for 4
cameras.

F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15
OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY
NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS
DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.

NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE
TO THE UNITS.  ANY CHANGES MADE TO THE UNITS
WILL VOID THE USER'S AUTHORITY TO OPERATE THE
EQUIPMENT.

Centers
each
camera
position.

Sweeps
thru the 4
stored
positions
for the
selected
camera.