The Genie Company a Division of Overhead Door Corporation ACSDA1 Benutzerhandbuch

Activate programming mode.

• Press (in order)

.

– Red LED blinks - once per second.

• Enter your PIN (3 to 8 characters).

• Press                 .

– Red LED blinks - twice per second and turns off.

Activate programming mode.

• Press (in order)

.

– Red LED blinks - once per second.

• Enter your PIN (3 to 8 characters).

• Press                 .

– Red LED blinks - twice per second and turns off.

¤

1 Keep people clear of opening while door is moving.
2 Do Not allow children to play with Wireless Keypad.
3 During programming, the door opener could begin to run, so stay away from the 

moving door and its parts. To keep the door from moving, close the door and  
disconnect it from the Opener by pulling the Emergency Release.

3528135342

To move the garage door:

• Enter your PIN.

• Press                            .

Find the Learn Code Button and Learn Code 
Indicator LED on your door opener.

– If your door opener has a 

black antenna wire,
the Learn Code Button 
and Indicator LED 
are located near the antenna.
(The light lens may need 
to be opened.)

– If your door opener does not

have an antenna,
you have  an external receiver.
The external receiver cover 
must be removed to access 
the Learn Code Button 
and Indicator LED.

• Press the Learn Code Button.

– Learn Code Indicator LED (on Opener) will blink.

• Enter your PIN and press                            on keypad.

– Learn Code Indicator LED stays on.

• Press                            again.

– Learn Code Indicator LED turns off.

Red Indicator
LED

Learn 
Code 
Button

Located
on Opener
Housing

Decide which door will be door #1,#2 and #3.

• Press the Learn Code Button (see Section 1 Step 2).

– Learn Code Indicator LED (on Opener) blinks.

• Enter your PIN and press                            .

– Learn Code Indicator LED stays on.

• Press the number you have picked for this

door Opener (              or              or              ).

– Learn Code Indicator LED stays on.

• Press                            .

– Learn Code Indicator LED turns off.

Repeat step A above for each door opener.
Each door opener must be programmed to receive  the 
signal from the Wireless Keypad.

To move one of the doors.

• Enter your PIN.

• Press                            .

• Press door opener number (              or              or              ).

Mount Keypad.(Mounting screws located inside 
battery compartment.)

• Remove Battery Cover. See Section 4 Figure 2.

• Drill a 1/16”pilot hole for the top mounting screw.

• Install a screw into the drilled 

hole,leaving a 1/8" gap 
between the screw head
and the wall. See Figure 1.

• Hook the Keypad over 

the screw.

• Mark,drill pilot hole and 

fasten bottom screw.

• Reinstall Battery Cover.

Program Keypad BEFORE mounting.

Enter your PIN

• Press                                                             .

Enter the Temporary PIN (from 3 to 8 characters).

• Press                    .

DO NOT reprogram the Door Opener(s).

Temporary PIN remains active until  the next time your 
normal PIN is entered.

Erase old PIN :

• Press and hold in order - 

.

– Red LED will blink once and turn off.

• Release all buttons.

Programming Door Opener(s).

• Return to “Programming”Section 1 or Section 2.

If the door does not move,check the red LED on Keypad.
If the LED is blinking rapidly,the PIN was entered 
incorrectly. After the LED stops blinking,re-enter your 
PIN and try again.

Any Keypad Button will control the door for 30 seconds  
after the door starts moving.

Rapid blinking of the red LED indicates an error. After a 
few seconds the LED will turn off. Start over.

Wall

screw head gap

Program Keypad BEFORE mounting.

• Enter your PIN and press

.

–  Red LED blinks - once per second.

• Press                     again.

– Red LED blinks - twice per second.

• Press the number of doors (total) you wish

to control (               or               ).

• Press                    .

– Red LED blinks several times and turns off.

1 Close door and disconnect the Opener using Emergency Release Cord.
2 Do not use door Opener, Remote Controls, or Wireless Keypad.
3 Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.

1"
8

Printed in the U.S.A.

©2003 The Genie Company, D.B.A. GMI Holdings, Inc.

This device complies with FCC Part 15 and RSS 210 of Industry Canada. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures: 1. Re-orient or 
relocate the receiver antenna. 2. Increase the separation between the opener and receiver. 3. Connect the
opener into an outlet on a circuit different from that to which the appliance is connected. 4. Consult the dealer.
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to 
operate the equipment.

9V

Battery

Press here

Bottom
Mounting
Screw

Red LED