The Genie Company a Division of Overhead Door Corporation GWWCP Benutzerhandbuch

Installation and Operation Instruction

39884503882, 02/2018

• DO NOT install wall console unless the door operator’s safety device works as required by 

the door operator’s manual.

• Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of 

moving door parts.

• Keep people clear of opening while door is moving.

• DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly:

• Close door then disconnect opener using the manual release handle.

• DO NOT use transmitter or door operator.

• Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.

• DO NOT install wall console unless the door operator’s safety device works as required by 

the door operator’s manual.

• Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of 

moving door parts.

• Keep people clear of opening while door is moving.

• DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly:

• Close door then disconnect opener using the manual release handle.

• DO NOT use transmitter or door operator.

• Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.

For questions, comments or troubleshooting, contact The Genie Company at:

1 Door Drive, Mount Hope Ohio, 44660

or call 1-800-354-3643 or visit our website at:

www.geniecompany.com

Learn Button Type

Program Button Types

(All others)

Openers compatible with the 

Wireless Wall Console include 

one model that programs with a 

LEARN BUTTON.

All other models use the 

PROGRAMMING BUTTON type. 

All programming button types, 

although appear different, 

program identically and are the 

most common.

NOTE: Once in programming mode, you will have approximately 30 seconds to complete programming.

FIG. 1

FIG. 2

Learn

PRGM

Open cover and remove 

battery tab before 

programming

Lower mounting slot

AAA

Door & Delay buttons operate all Genie Intellicode® openers.

Light button operates Genie Intellicode® openers produced 2013 or later.

1.  Press and hold the program button on the opener until the round LED turns blue, then 

release.

2.  The round LED will go out and the long LED will begin flashing purple. Fig. 3. 

3.  Press the DOOR button on the WALL CONSOLE 3 times or until door operates.

1.  Press and release the LEARN CODE button on the opener. Its RED LED will begin to 

flash. 

2.  Press the DOOR button on the WALL CONSOLE 3 times or until door operates.

1. DOOR Button - Runs garage door opener.
2. DELAY Button - Adds a 10+ second delay for door operation. Press the 

delay button and door will automatically operate after set delay.

3. LIGHT Button - Overrides the automatic  timed light function of the 

garage door opener.

1
2

3

AAA

Wall Consoles should be mounted at least 5 feet from floor in a convenient location within 

sight of the garage door.

•  Remove battery cover, battery activation tab and batteries.

1. Drill a 3/32” pilot hole for the bottom mounting screw.

2. Install included screw into pilot hole, leaving 1/8” gap between the screw head and wall.

3. Hook the slotted mount on back of Wall Console over the screw.

4. Mark and drill a 3/32” pilot hole for the top screw.

5. Secure Wall Console to the wall. (Do not over-tighten).

6. Reinstall batteries and battery cover.

1. Drill a 3/32” pilot hole for the bottom screw insert.

2. Lightly tap drywall anchor into hole with a hammer until flush with wall.

3. Install included screw into anchor, leaving 1/8” gap between the screw head and wall.

4. Hook the slotted mount on back of Wall Console over the screw.

5. Mark position of pilot hole for the top insert and remove wall console.

6. Drill 8/38” pilot hole for top drywall anchor.

7. Lightly tap anchor into hole with a hammer until flush with wall.

8. Secure Wall Console to the wall. (Do not over-tighten).

9. Reinstall batteries and battery cover.

NOTE: Any changes to the Blue LED blink rate other than the default setting will impact battery 

BLUE LED Blink rate Mode 1 (Default - Once every 3 seconds)

With only (1) AAA battery installed - hold down the DOOR button while simultaneously 

installing the second AAA battery.  Continue to hold the DOOR button for a total of 10 

seconds until the LED flashes 3 times letting you know your selection is complete

BLUE LED Blink rate Mode 2 (Faster Blink Rate - Once every 2 seconds)

With only (1) AAA battery installed - hold down the LIGHT button while simultaneously 

installing the second AAA battery.  Continue to hold the LIGHT button for a total of 10 

seconds until the LED flashes 3 times letting you know your selection is complete.

BLUE LED Blink rate Mode 3 (Blue LED OFF - Maximum Battery Life)

With only (1) AAA battery installed - hold down the DELAY button while simultaneously 

installing the second AAA battery.  Continue to hold the DELAY button for a total of 10 

seconds until the LED flashes 3 times letting you know your selection is complete.

Mounting

Screws

Drywall

Anchors

-OR-

The default delay period is set for a 10 second delay. Once the DELAY button has been 

pressed the operation can’t be canceled unless the same console DOOR button is pressed. 

During the activation of a delay operation consecutive button presses will add 10 seconds 

to the delay time. Up to 3 consecutive button presses for a total of 30 seconds can be 

made. At any point in time during a delay operation, a DOOR button press will disable the 

current delay operation

The Wireless Wall Console includes self diagnostic LEDs

1. LED Blue Blink = Indicates NORMAL status.

2. LED Red Blink = Indicates low battery. 

-OR-