Modern Co. Ltd. TR1003 Benutzerhandbuch
9
ELECTRONICIGNITIONSYSTEMS
Please DO take following tests and make sure all functions are working fine:
1. Slide the slide switch button on the receiver to the ON (Fig. 16). The spark igniting electrode should begin
sparking to ignite the pilot. Once the pilot flame is lit, the main gas valve should open and the main gas fire flame should
be ON.
be ON.
2. Slide the button to OFF. The main gas fire flame and pilot fire flame should extinguish together.
3. Slide the button to REMOTE, and then press the MODE button on the transmitter to change the system to ON.
The spark igniting electrode should begin sparking to ignite the pilot. Once the pilot flame is lit, the main gas valve should
open and the main gas fire flame should be ON.
open and the main gas fire flame should be ON.
4. Press the MODE button to OFF. The main gas fire flame and pilot fire flame should extinguish together.
5. Press the MODE button on the transmitter to change the system to THERMO
*2
. Make the SET temperature on
the transmitter to a temperature of a least 2°F (1°C) above the ROOM temperature displayed on the LCD screen, the
system flame and main gas fire flame will be ON. Then make the SET temperature to at least 2°F (1°C) below the
ROOM temperature, the system flame and main gas fire flame will extinguish in seconds. It should continue to cycle ON
and OFF thermostatically. The temperature differential between ROOM and SET temperatures differ at least 2°F (1°C)
to start the THERMO
system flame and main gas fire flame will be ON. Then make the SET temperature to at least 2°F (1°C) below the
ROOM temperature, the system flame and main gas fire flame will extinguish in seconds. It should continue to cycle ON
and OFF thermostatically. The temperature differential between ROOM and SET temperatures differ at least 2°F (1°C)
to start the THERMO
*2
cycling. (The 2°F differential is the factory setting, can NOT be changed.)
ADDITIONALINFORMATION
THERMOSAFETYPROTECTION FORRECEIVER
In order to protect the receiver box, batteries, and receiver’s microprocessors, the Durablow remote control system
equips a THERMISTOR, a safety feature in receiver box.
equips a THERMISTOR, a safety feature in receiver box.
The THERMISTOR will automatically shut the system and appliance down,& begin makingBEEP X 3 (♫, ♫, ♫), every 4
seconds, when the temperature inside the receiver boxis higher than 130°F (54°C). User can re-activate the system by
pressing the MODE button on the transmitter when the receiver temperature drops between 120°F (48°C) and 130°F
(54°C).
seconds, when the temperature inside the receiver boxis higher than 130°F (54°C). User can re-activate the system by
pressing the MODE button on the transmitter when the receiver temperature drops between 120°F (48°C) and 130°F
(54°C).
However, the BEEPING will NOT stop if the temperature remains between 120°F and 130°F until the temperature drops
below 120°F. The beeping is to alert user that the receiver should be re-located at a cooler position.
below 120°F. The beeping is to alert user that the receiver should be re-located at a cooler position.
To completely reset the beeping and
THERMISTOR, please press the MODE button to make a mode cycle (OFF-ON-
OFF). Please make sure & allow some time for the receiver box to cool down below 120°F .
TRANSMITTER
1.
TRANSMITTEROPERATINGDISTANCE
Thetransmitter uses RF radio frequency to send signal to receiver. Itis strongly recommendedtouse thetransmitter
within20-foot distance from receiver box in the same room / space (no wall partition).
within20-foot distance from receiver box in the same room / space (no wall partition).
2. THERMO
*2
DETECTING INTERVAL IN TRANSMITTER
The transmitter normally detects the ROOMtemperature every 2 minutes against theSETtemperature by sending a signal
tothe receiver.
tothe receiver.
3. OUT-OF-RANGE SAFETY ALERT IN TRANSMITTER
Page 8