AMERICAN DIRECT INC WL-12 Benutzerhandbuch
FCC Statement
This device complies with Part of the FCC Rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) this device must accept
any interference received, including interference that may cause undesired operation.
conditions: 1) This device may not cause harmful interference, and 2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digi-
tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate harmful interference to radio communications.
tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception (which can be
determined by turning the equipment off and on) the user is encouraged to try to correct the
interference by one or more of the following measures;
this equipment does cause harmful interference to radio or television reception (which can be
determined by turning the equipment off and on) the user is encouraged to try to correct the
interference by one or more of the following measures;
IMPORTANT:
Remove batteries if left unused for long periods.
Do NOT use different types of batteries at the same time.
Do NOT mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
Only recommended batteries are to be used.
Alkaline batteries are recommended for best use.
Do NOT use new and old batteries at the same time.
Do NOT attempt to re-charge non-rechargeable batteries.
Rechargeable batteries are only to be charged under adult supervision.
Be sure to install batteries with the polarities aligned correctly.
When batteries are exhausted, remove them to prevent damage or danger.
Do NOT attempt to short circuit the terminals.
Do NOT dispose of in a fire as batteries may explode or leak.
Do NOT use different types of batteries at the same time.
Do NOT mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
Only recommended batteries are to be used.
Alkaline batteries are recommended for best use.
Do NOT use new and old batteries at the same time.
Do NOT attempt to re-charge non-rechargeable batteries.
Rechargeable batteries are only to be charged under adult supervision.
Be sure to install batteries with the polarities aligned correctly.
When batteries are exhausted, remove them to prevent damage or danger.
Do NOT attempt to short circuit the terminals.
Do NOT dispose of in a fire as batteries may explode or leak.
R E A D C A R E F U L L Y B E F O R E F I R S T U S E
Unlike ordinary infared battery operated lights, Wherever Lite operates on radio
frequency. This means that the Wherever Lite remote works up to 50 feet away,
through walls, doors, furniture, and more–without interference!
frequency. This means that the Wherever Lite remote works up to 50 feet away,
through walls, doors, furniture, and more–without interference!
HOW TO INSTALL BATTERIES ON THE WIRELESS REMOTE CONTROL
1. Locate the battery compartment on the back of the remote.
2. Place 2 “AAA” batteries inside, making sure the polarities are properly matched.
1. Locate the battery compartment on the back of the remote.
2. Place 2 “AAA” batteries inside, making sure the polarities are properly matched.
Match “+” and “-” symbols that are on the battery ends to the marks inside the
battery compartment.
battery compartment.
3. Replace and close the cover.
HOW TO INSTALL BATTERIES ON WHEREVER LITE
1. Locate the battery compartment on the bottom of the light. Turn the cover
1. Locate the battery compartment on the bottom of the light. Turn the cover
counter-clockwise and remove.
2. Place 3 “AA” batteries inside, making sure the polarities are properly matched.
Match “+” and “-” symbols that are on the battery
ends to the marks inside the battery compartment.
ends to the marks inside the battery compartment.
4. Replace cover and turn clockwise to close.
ABOUT INDIVIDUAL AND GROUP LIGHTING
INDIVIDUAL: Your Wherever Lite comes all
ready to use if you plan to use one Wireless
Remote Control with one Wherever Lite!
ready to use if you plan to use one Wireless
Remote Control with one Wherever Lite!
GROUP: You can program the Wireless Remote
Control to operate multiple Wherever Lites from
the press of a button and set up is a breeze!
Control to operate multiple Wherever Lites from
the press of a button and set up is a breeze!
On the back of the Wireless Remote Control,
locate the code switch as shown in Fig 1.
Flip the switches to a combination of your choice.
On the back of your Wherever Lite,
open the battery compartment cover
and locate the code switch.
Flip the switches to match the
combination code that you entered
on your Remote.
Replace the battery compartment
cover and repeat the process with
the rest of the Wherever Lites in
the grouping.
the grouping.
NOTE: It is not recommended to
exceed 20 lights per grouping.
exceed 20 lights per grouping.
HOW TO INSTALL WIRELESS REMOTE
CONTROL AND WHEREVER LITE
CONTROL AND WHEREVER LITE
WIRELESS REMOTE CONTROL–Use the “keyhole” on the back of the remote to screw
mount, OR, peel off the adhesive paper on the back and stick it to the desired location.
mount, OR, peel off the adhesive paper on the back and stick it to the desired location.
WHEREVER LITE–Remove the battery compartment on the back of the Wherever Lite and
attach it to the desired location using screws, OR peel and stick on the back and stick it to
the desired location.
attach it to the desired location using screws, OR peel and stick on the back and stick it to
the desired location.
HOW TO USE THE LIGHT
1. You can operate the Wherever Lites either by switching the remote to the “On” position,
1. You can operate the Wherever Lites either by switching the remote to the “On” position,
OR you can simply press the center of the Wherever Lite.
2. To use dim the light, simply press and hold the “On” position on the remote.
3. To turn light off, either switch the remote to the “Off” position, OR press the center
3. To turn light off, either switch the remote to the “Off” position, OR press the center
of the light.
HOW TO USE THE BUILT-IN TIMER
On the side of the Wireless Remote Control there is a switch for three built-in timer
functions. By choosing one of these settings, your light will automatically shut off after
either 15 minutes, or 30 minutes, to preserve battery life.
On the side of the Wireless Remote Control there is a switch for three built-in timer
functions. By choosing one of these settings, your light will automatically shut off after
either 15 minutes, or 30 minutes, to preserve battery life.
FIG. 1
FIG. 2
Adjust
switches
to desired
settings
switches
to desired
settings
Size: 105(x2)mm x140mm
140mm
105mm
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an autlet on a circuit different from that to
- Connect the equipment into an autlet on a circuit different from that to
which the receiver is connectec.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
0RGHO:/