Transition Networks CRS2F3113-100 Merkblatt

Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA

tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com

©2011 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.

Specifications

Standards

EIA/TIA-574, EIA/TIA RS-232E

Data Rate

115 Kbps

Switches

DTE/DCE: Select appropriate position
Loop-back: Norm = normal operation;
Loop = Fiber and copper loop-back

Status LEDs

P (Power): Lit for normal operation
RX: Steady = Copper Link; Flashing = Rx Data
FL: Steady = Fiber Link; Flashing = Loop back mode

Dimensions

Width: 0.86" [22 mm]
Depth: 5.0" [127 mm]
Height: 3.4" [86 mm]

Power Consumption

5.0 Watts

Environment

See chassis specifications

Shipping Weight

1 lb. [0.45 kg]

Regulatory Compliance

CISPR22/EN55022 Class A + EN55024;
EN60950 Class A; FCC Class A; CE Mark

Warranty

Lifetime

Ordering Information

CRS2F3111-100

DB-9

[15 m/49 ft.]

to 1300nm multimode (ST)

[2 km/1.2 mi.] Link Budget: 11.0 dB

CRS2F3113-100

DB-9

[15 m/49 ft.]

to 1300nm multimode (SC)

[2 km/1.2 mi.] Link Budget: 11.0 dB

CRS2F3114-100

DB-9

[15 m/49 ft.]

to 1310nm single mode (SC)

[20 km/12.4 mi.] Link Budget: 16.0 dB

CRS2F3115-100

DB-9

[15 m/49 ft.]

to 1310nm single mode (SC)

[40 km/24.9 mi.] Link Budget: 26.0 dB

CRS2F3129-100

DB-9

[15 m/49 ft.]

to 1310TX/1550RX single fiber SM (SC)

[20 km/12.4 mi.] Link Budget: 19.0 dB

CRS2F3129-101

DB-9

[15 m/49 ft.]

to 1550TX/1310RX single fiber SM (SC)

[20 km/12.4 mi.] Link Budget: 19.0 dB

CRS2F3129-102

DB-9

[15 m/49 ft.]

to 1310TX/1550RX single fiber SM (SC)

[40 km/24.8 mi.] Link Budget: 25.0 dB

CRS2F3129-103

DB-9

[15 m/49 ft.]

to 1550TX/1310RX single fiber SM (SC)

[40 km/24.8 mi.] Link Budget: 25.0 dB

Link a remote terminal to a host computer: Connect multiple devices, such
as security scanners, POS devices, remote terminals and building
access/alarming systems to a host computer.

Transition Networks’ serial RS232 to Fiber converters allow you to extend
the distance between serial connections with the use of fiber optic cable.
These full-featured converters transmit the full complement of RS232 flow
control/handshaking signals optically and supports full or half-duplex asyn-
chronous data transmission at speeds up to 115 Kbps.

The diagnostic features included on these converters make installation easy
and intuitive. A DTE/DCE switch eliminates the frustration over selecting the
appropriate cable. A Loopback [pg 18] switch allows for complete diagnos-
tic testing prior to system turn-up or during troubleshooting. Unit and Port
LEDs allow for quick status information of the device.

Ideal for campus or business
environments where remote de-
vices can be networked in a point
to-point configuration and dis-
tances are greater than the 15 m
limitation of conventional copper
serial cables.

Extend Network Distance

CRS2F311x-100

point system™ slide-in-module media converter

Features

Read/write access to remote

stand-alone unit

Local or Remote Loopback on

copper and fiber

DTE/DCE switch for easy

installation with straight-
through cabling

Full/Half-duplex asynchronous

transmission at speeds up to
115 Kbps

Supports the following flow

control signaling:

1. DCD - Data Carrier Detect
2. RXD - Receive Data
3. TXD - Transmit Data
4. DTR - Data Terminal Ready
5. SG - Signal Ground
6. DSR - Data Set Ready
7. RTS - Request To Send
8. CTS - Clear To Send

Field Upgradeable Firmware

RS232 Copper to Fiber with

Remote Management

RS232