Gosuncn Technology Group Co. Ltd. GW521 Benutzerhandbuch
1
2
3
4
5
DC IN
LAN1-LAN4
LAN1-LAN4
RESET
WLAN
WPS
SIM
WPS
SIM
LTE Indoor CPE
Quick Start Guide
WELCOME
TO THE LTE CPE
This document will serve as a quick start guide for LTE indoor
device. In this document, the LTE CPE will be called CPE for
short. Please read the following safety symbols carefully to
help you use the CPE safely and correctly.
device. In this document, the LTE CPE will be called CPE for
short. Please read the following safety symbols carefully to
help you use the CPE safely and correctly.
Please insert your SIM card as following:
The figure is just for reference only, please connect the
hardware according to your requirements.
hardware according to your requirements.
When you are using the CPE, you can adjust the position
and direction of CPE to get stronger LTE signal, judging
from the LTE signal LED indication.
and direction of CPE to get stronger LTE signal, judging
from the LTE signal LED indication.
Step 1 Connect the power adapter to the CPE.
The figures provided in this document are just for
reference only, please refer to the actual which shall
govern.
reference only, please refer to the actual which shall
govern.
If you want to remove the SIM card, please lightly press the
SIM card, the SIM card will pop out. Make sure the CPE is
turned off before you insert or remove your SIM card.
Otherwise, the CPE and SIM card may be damaged.
SIM card, the SIM card will pop out. Make sure the CPE is
turned off before you insert or remove your SIM card.
Otherwise, the CPE and SIM card may be damaged.
Additional information
Optional methods or shortcuts for an action
Potential problems or conventions that need to be
Optional methods or shortcuts for an action
Potential problems or conventions that need to be
specified
Package Contents
Please check the package contents before installation:
> LTE CPE
> Power adapter
> LTE CPE
> Power adapter
If you find anything missing or damaged, please contact
your local service suppliers.
your local service suppliers.
> Ethernet cable
> Quick Start Guide
> Quick Start Guide
GETTING STARTED
Equipment Appearance
1
2
3
4
5
6
7
8
9
10
11
12
13
14
POWER Indicator
Wi-Fi Indicator
WPS Indicator
LTE Status Indicator
LTE Signal Indicator
WPS Button
Reset Button
Wi-Fi Button
Power Switch
DC Jack
LAN Port
SIM Card Slot
LAN Indicator
Label
LED INDICATION
LAN
POWER
LTE
Wi-Fi
SIGNAL
WPS
LED
Indicator
LED
States
Description
Power supply normal
No power supply
Wi-Fi is enabled
Wi-Fi is disabled
Data is transferred through Wi-Fi
WPS is enabled
WPS is disabled
Wi-Fi access authentication in progress.
Resisted to LTE
Detecting no SIM card
No power supply
Wi-Fi is enabled
Wi-Fi is disabled
Data is transferred through Wi-Fi
WPS is enabled
WPS is disabled
Wi-Fi access authentication in progress.
Resisted to LTE
Detecting no SIM card
Detected USIM Card, searching LTE network
Indictor LTE signal Strength.
No LTE signal
Ethernet connection is normal.
Ethernet connection is not established.
Ethernet interface data being transmitted.
No LTE signal
Ethernet connection is normal.
Ethernet connection is not established.
Ethernet interface data being transmitted.
On
Off
On
Off
Blink
On
Off
Blink
Blue LED On
Red LED On
Blue LED
Blinking
On
Off
On
Off
Blink
Off
On
Off
Blink
On
Off
Blink
Blue LED On
Red LED On
Blue LED
Blinking
On
Off
On
Off
Blink
SET UP THE HARDWARE
Insert SIM Card
HARDWARE CONNECTION
・
You can connect your computer or classic Switch via
Ethernet cable to LAN port.
・
・
You can connect your laptop via Wi-Fi.
Step 2 Power on CPE.
9 10
11
12 13
14
PN: 6061A4420323
Step 3 Connect other devices.
INTERFACE AND BUTTON
Interface & button Description
DC power input port
Connet computer, switches (non PoE devices)
Connet computer, switches (non PoE devices)
or other LAN devices
Press 1s to reboot device.
Press 1s to reboot device.
Press 10s and more, CPE will restore to factory mode.
You will lost user defined setting once you reset CPE.
So, be cautious to click Reset Button.
WLAN button
WPS PBC button
USIM Slot
WPS PBC button
USIM Slot
Special LED status 1: when upgrading firmware, WPS and Wi-Fi LED will blink.
Special LED status 1: when resetting CPE, All LED will be on except signal LED.
Special LED status 1: when resetting CPE, All LED will be on except signal LED.