RadioShack Corporation 3301197T Benutzerhandbuch

Please read this user’s guide before

installing, setting up and using your new product

www.radioshack.com

33-1197

Rechargeable Analog Wireless

Stereo Headphones

Thank you for purchasing RadioShack Rechargeable

Analog Wireless Stereo Headphones. It is designed with

PLL (Phase-Locked Loop) circuitry and built-in antenna

for precise tuning. It uses the 900MHz band to deliver

high-quality stereo sound to almost anywhere in or

around your home, up to 150 feet away from your stereo.

Rechargeable Analog Wireless Stereo

Headphones

1/8-to-1/4-inch stereo adapter

1/8-inch stereo plug adapter

RCA cable

12V, 250mA AC/DC adapter

User’s Guide

what’s included

You need to power the transmitter by the

supplied 12V, 250mA AC/DC adapter when you

use the headphones.
Plug the supplied AC adapter’s barrel plug

into the transmitter’s DC IN 12V jack, then

plug the adapter into a standard AC outlet.

• Use only 12V DC,250mA AC/DC

adapter to power the transmitter.

• Always connect the AC/DC adapter

to the transmitter before you connect

it to AC power. When you ﬁnish,

disconnect the adapter from AC

power before you disconnect it from

the transmitter.

power the transmitter

Installing the batteries
The headphones requires three AAA alkaline

batteries or Ni-Ca/NiMH rechargeable batteries

(neither supplied) for power.
1. Remove the battery compartment cover on

the left earpiece.

2. If you are using alkaline batteries, set ALK/

RCH inside the compartment to ALK. If you

are using rechargeable batteries, set ALK/

RCH to RCH.

3. Place the batteries in the compartment

according to the polarity symbols (+ and –)

marked in the compartment.

4. Replace the battery compartment cover.

charging rechargeable batteries
The transmitter has a built-in charger. You can

use the transmitter to charge rechargeable

batteries(700mAh,not supplied) in your

headphones.
1. Place the

headphones on

the transmitter

and power the

transmitter

to charge the

rechargeable

batteries, the

transmitter’s

CHARGE indicator

lights up green.

• Rechargeable batteries can be

continuously charged over several

days.

• The batteries can be charged with the

transmitter set to on or off.

• When the batteries have been

completely discharged, it takes about

10 hours to completely recharge the

batteries.

2. The CHARGE indicator turns off when

charging is completed, remove the

headphones from the transmitter.

power the headphones

Note

1. Connect one end of the supplied audio

patch cord to the transmitter’s AUDIO IN

jacks (white plug to L AUDIO IN and red

plug to R AUDIO IN).

2. Follow one of the steps below to connect

the transmitter to your audio source.

• If your audio source’s has output jacks,

connect the white and red plugs at the

other end of the RCA cable directly to

the audio source’s corresponding left

(white) and right (red) audio jacks.

• If your audio source has a 1/8-inch

headphones jack, connect the white

and red plugs of the RCA cable to the

white and red phono jacks of the 1/8-

inch stereo plug adapter. Then insert

the adapter into the audio source’s

headphones jack.

• If your audio source has a 1/4 -inch

headphones jack, insert the 1/8-inch

stereo plug adapter into the back of the

supplied 1/8-to-1/4-inch stereo adapter.

Then insert the adapter into the audio

source’s HEADPHONE jack.

3. Power the transmitter.

installing your headphones

1/8-inch

stereo

plug

adapter

1/8-to-1/4-inch

stereo adapter

ALK/RCH

CHARGE

indicator

POWER

indicator

Power

AUDIO

jacks

RCA cable

12V, 250mA AC/DC adapter

transmitter

33-1197.indd 1

11/02/2005 5:08:26 PM